MinimumRC F6F Hellcat Assembly Instructions Manual Download | Manualshive

Page: 1 / 18

background image

F6F Hellcat Q-Series

Assembly Instructions

Important notification

1.The model is supplied with UFO and 502 glue. UFO is for bonding foam parts, and 502 for

bonding wood, carbon fiber and metal parts. 502 glue will cause serious corrosion to foam parts.
2.Please wait for the glue to dry and solidify in each installation step before the next installation.

3.Please avoid using flame to heat the heat shrinkable tube on the model. Electric iron shall be
used for heating.
4.Please use razor blade to remove the parts from the plate. Do not tear the parts by force.

1
2
3
...
»

Summary of Contents for F6F Hellcat



















Reviews:

No comments

Related manuals for F6F Hellcat

Brand: Advance acoustic Pages: 18

Brand: Advance acoustic Pages: 18

Brand: Advance acoustic Pages: 18

Brand: Advance acoustic Pages: 20

Brand: Advance acoustic Pages: 22

Slingshot 1.0 PNP

Brand: Tomahawk Pages: 2

Brand: Meridian Pages: 630

Brand: F-One Pages: 13

Brand: Topmodel CZ Pages: 15

Brand: DUOTONE Pages: 24

Brand: Tecnam Pages: 67

P92 Echo Classic Jabiru

Brand: Tecnam Pages: 67

Brand: Naish Pages: 13

Brand: Kavan Pages: 24

Brand: Guimbal Pages: 156

Brand: Icarus Pages: 36

Brand: Topmodel CZ Pages: 12

Brand: MAC PARA Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands