MIMAKI Kebab MKII Operation Manual Download

Page: 1 / 56

MIMAKI ENGINEERING CO., LTD.

https://mimaki.com/

D203140-20

TABLE OF CONTENS

Foreword ...........................................................................................2

DISCLAIMER OF WARRANTY .......................................................... 2
Requests ............................................................................................. 2
Interference to televisions and radios ................................................. 2

For safe operation ............................................................................3

Symbols .............................................................................................. 3

Configuration and Function .............................................................9

Front view of Kebab MkII system ........................................................ 9
Rear view of Kebab MkII system ........................................................ 9
Front view of Kebab MkII L system ................................................... 10
Rear view of Kebab MkII L system ................................................... 10

Usable works ...................................................................................11
Installation of Kebab MkII system .................................................12

Attach Kebab MkII/Kebab MkII L system ......................................... 12
Attach Kebab MkII system on UJF-3042MkIIseries .......................... 12
Remove the Kebab MkII system from UJF-3042MkIIseries  ............. 16
Attach Kebab MkII L system on UJF-6042MkIIseries ....................... 19
Remove the Kebab MkII L system from UJF-6042MkIIseries  .......... 23
Attach Kebab MkII L system on UJF-7151 plus series  ..................... 26
Remove the Kebab MkII L system from UJF-7151 plus series ......... 29

Set a work ........................................................................................31

Set a work ......................................................................................... 31
Attention when using a work of the different diameter from the previous-
ly used work ...................................................................................... 32

Use the work holder  .......................................................................33
Remove the work holder  ................................................................36
Use the origin mark detection  .......................................................37

Set the origin mark detection ............................................................ 37
Use the origin mark ........................................................................... 38
When not using the Origin mark sensor ........................................... 39
Responding to “ERROR 524 WORK ORIGN MARK” ....................... 40

Set the start position of drawing ...................................................41
Create data to be drawn .................................................................42

Measure the work size ...................................................................... 42

Test drawing ....................................................................................43
Enable Kebab printing ....................................................................44
Drawing an image from source data .............................................45

Starting the drawing operation .......................................................... 45
Interruption of drawing ...................................................................... 47

Maintenance ....................................................................................52

Cleaning the roller shafts .................................................................. 52
Cleaning the Origin mark sensor ...................................................... 53

Specifications .................................................................................54

Summary of Contents for Kebab MKII

























































Search results

Summary of Contents for Kebab MKII

Reviews:

Related manuals for Kebab MKII

Brands by name

Popular brands

MIMAKI Kebab MKII, Operation Manual

Search results

Summary of Contents for Kebab MKII

Reviews:

Related manuals for Kebab MKII

Brands by name

Popular brands