MillRight CNC MEGA V XXL Assembly Instructions Manual Download | Manualshive

Page: 1 / 32

background image

1 of 32

ASSEMBLY INSTRUCTIONS FOR THE MILLRIGHT CNC MEGA V XXL

Version 1.01

For additional resources, see

www.millrightcnc.com/resources

Be sure to check the resources page for the most updated assembly instructions.

Contact

[email protected]

if you have questions.

We have a big online community. Be sure to join in the discussion.

Facebook MillRight CNC Group

Facebook MillRight Mega V Group

MillRight CNC Forum at www.millrightcnc.proboards.com

Important safety rules for operating your MillRight CNC Mega V XXL:

Never place your hands near a spinning end mill or bit.
Always wear eye and ear protection while operating your machine.
Always run a dust collector or wear a mask while performing a milling operation.
Do not leave the machine unattended while running a milling operation.
Do not operate your machine while under the influence of alcohol or drugs.
Secure long hair and loose clothing so it is not caught in spinning mechanisms.
Ensure work pieces are properly secured before running a milling operation.
Keep a fire extinguisher nearby.
Visually inspect wires prior to power up to prevent short circuits.

The Mega V XXL is a big, heavy machine. Plan on spending a full weekend in assembly and seeking help with moving or
flipping heavy assemblies.

We recommend using a blue thread locker on any fastener not secured with a lock washer or lock nut.

1
2
3
...
»

Summary of Contents for CNC MEGA V XXL

































Reviews:

No comments

Related manuals for CNC MEGA V XXL

Brand: Shenyang 245 Factory Pages: 28

Brand: Pragati Pages: 32

Brand: Powermatic Pages: 2

Brand: Powermatic Pages: 44

Brand: Rikon Power Tools Pages: 16

Brand: Baileigh Pages: 25

Brand: King Industrial Pages: 7

Brand: King Industrial Pages: 11

Brand: King Industrial Pages: 13

Brand: King Industrial Pages: 27

Brand: Central Machinery Pages: 22

434-08-651-0001

Brand: Delta Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands