01OVLPA0510PB-V1 01OSBA510PB-V1 01SHPA0510PB-V1
Overall Dimensions:
Length = 1502mm
Width = 2259mm
Height = 3094mm
Base Dimensions:
Length = 1487mm
Width = 3094mm
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
This building should be erected by
two adults
For ease of assembly, you must pilot
drill all screw holes and ensure all
screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be affected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on firm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run off for water. It is also
recommended that the floor be at least 25mm above the surrounding ground level to avoid flooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71
level, we cannot accept responsibility for your safety whilst erecting or using this product.
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every effort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
01OSBA0510PB-V1
01OVLPA0510PB-V1
01SHPA0510PB-V1
Plain Side
Window Side
Floor
Qty 2
Roof Sheet
Qty 2
Building content for:
01OVLPA0510PB-V1 & 01OSBA0510PB-V1
(Check building label for product code)
Ridge Bar - 1486mm Qty 2
Truss Block - 140mm Qty 2
Cover Trim - 1575mm Qty 2
Window Strip - 546mm Qty 5
Floor Blocks - 400mm Qty 8
Eaves Frame - 1502mm Qty 2
Plastic Window Cill
Felt
Styrene
Qty 2
Building content for:
01SHPA0510PB-V1
(Check building label for product code)
Plain Side
Window Side
Floor
Qty 2
Middle Roof
Qty 2
Ridge Bar - 1486mm Qty 2
Truss Block - 140mm Qty 2
Cover Trim - 1575mm Qty 2
Opening Window Strip - 1155mm Qty 1
Floor Blocks - 400mm Qty 8
Eaves Frame - 1502mm Qty 2
Felt
Opening Window
Qty 2
Casement Stay
Butt Hinge
Qty 2
Truss
Truss
