![background image](http://html1.mh-extra.com/html/mazda/0000-8f-l10/0000-8f-l10_installation-instructions-manual_1751987001.webp)
1
1031012 Rev.A 09/05
LOCK
UN
LOCK
START
!
PART NUMBER (s):
0000-8F-L10
APPLICABLE MODELS:
2004>MAZDA3
All Models With
Power Door Locks
REMOTE START SYSTEM
WITH VEHICLE SECURITY
AND KEYLESS ENTRY
KIT CONTENTS
Remote Start DNA Card
Remote Start Dipole Antenna Remote Start
Control Module (QTY-1)
Transmitters (QTY-1)
Wire Harness
(QTY-1)
(QTY-2)
(QTY-1)
P/N: 0000-8F-Z01
P/N: 0000-8F-L16
P/N: 0000-8F-F06
P/N: 0000-8F-Z10
P/N: 0000-8F-L02
1. Disconnect negative battery terminal:
a. Remove relay cover by grasping rear of cover and pulling upwards.
Disengage locking tabs and remove cover. (FIGURE A)
b. Disengage locking tabs and remove cover the battery cover.
c. Disconnect negative battery terminal and isolate.
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
®
Owner's Manual
Vehicle Remote Start System
TM
Featuring PowerCode Technology
For the Ultimate in Comfort, Convenience and Security
TM
MAZDA
GENUINE ACCESSORIES
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
30
sec.
2 sec.
5X
2 sec.
Immobilizer Interface Adhesive Primer 2- Sided Tape
Module and Harness (QTY-1)
(QTY-1)
(QTY-1)
Tie Wrap
(QTY 2)
IDC Wire Tap
(QTY 2)
Hood Safety
Switch
(QTY 1)
Owners
Manual
(QTY 1)
Wallet
Card
(QTY 1)
Underhood
Sticker
(QTY 1)
Long Tie
Wrap
(QTY 3)
Mini Fuses
(QTY - (1) 5 AMP)
(QTY - (7) 15 AMP)
1/4” Self
Drilling Screws
(QTY 2)
PARTS BAG CONTENTS
HOOD SAFETY SWITCH KIT CONTENTS
(P/N: 0000-8F-H03)
Locking
Washer
(QTY 2)
TOOLS REQUIRED
SAFETY GLASSES
ELECTRICAL TAPE
WIRE CUTTERS
PLIERS
ALCOHOL or GLASS CLEANER
PHILLIPS SCREWDRIVER
POWER DRILL
9/32” DRILL BIT
FIBER STICK
10mm SOCKET AND RATCHET
1/4” SOCKET AND DRIVE
3/8” DRIVE TORQUE WRENCH
3/8” DRIVE 10mm SOCKET
0
IMMOBILIZER INTERFACE KIT CONTENTS
(P/N: 0000-8F-H05)
FIGURE A
1
VEHICLE PREPARATION
NOTE: BOTH PROGRAMMED
IGNITION KEYS ARE REQUIRED
AT TIME OF INSTALLATION
PRE INSTALLATION
1. CLEAN HANDS
2. OPEN DRIVER’S DOOR WINDOW
3. RECORD RADIO STATIONS
4. SET PARKING BRAKE
5. DISCONNECT AND ISOLATE
NEGATIVE BATTERY TERMINAL
6. VEHICLE MUST BE AT ROOM
TEMPERATURE
Tie Wrap LED IDC Wire Tap
(QTY-10) (QTY-1) (QTY-7)
& L10A