SCREEN DISPLAYS
rpm
Rev. counter screen
Partial hour meter screen
Hour meter screen
Maintenance reminder screen
!
Error code screen
SIGNAL LIGHTS
1 - Rev counter
2 - Engine coolant temperature
3 - Fuel level
4 - Forward/neutral/reverse lamp
5 - Orange air filter clogging lamp
6 - Orange hydraulic return oil clogging lamp
7 - Red general fault lamp
8 - Orange transmission oil temperature lamp
9 - Orange engine fault lamp
10 - Orange fuel level lamp
11 - Red battery charge lamp
12 - Not used
13 - Not used
14 - Not used
15 - Not used
16 - Red engine oil pressure lamp
17 - Red engine water temperature lamp
18 - Red parking brake lamp
19 - Red brake fluid level lamp
20 - Orange engine preheat lamp
21 - Water in fuel lamp
22 - Not used
23 - Indicator lights indicator lamp
24 - Front wheel alignment light
25 - Rear wheel alignment light
26 - Fast gear indicator light
27 - Slow gear indicator light
28 - Blue main beam headlights indicator
lamp
CONTROL AND SIGNAL LIGHTS PANEL
RAZ
h
km/h
km/h
milesmph
pm
°C
°F
l/h
wait
notice
%
am
rpm
rpm
mph
!
16
17
15
14
13
12
11
10
9
8
7
6
5
4
1
3
2
18
19
20
21
22
23
25
27
26
28
24
MT 625 H EASY 49K ST3A S1
THIS MACHINE IS AN ALL TERRAIN FORKLIFT TRUCK DESIGNED TO OPERATE ON NATURAL OR UNDEVELOPED LAND, OR CONSTRUCTION SITES.
t
IMPORTANT
t
This document is a short recap on how to drive a forklift truck, and should in no way be a substitute for the manual required by Directive 2006/42/EC Annex I section 1.7.4, which should
be read and understood by the operator beforehand and is available in the forklift truck’s cab.
All instructions, including safety instructions, which are in the manual but are not included in this document should be implemented and enforced.
The operator must have received proper training and must comply with the rules in force on road traffic.
BASIC INSTRUCTION SHEET No. 52519582EN (21/07/2017)
WEIGHT OF FORKLIFT TRUCK WITH STANDARD ATTACHMENT
(TRANSPORT POSITION)
- Unladen
- At rated load
- On front axle (unladen)
- On rear axle (unladen)
- On front axle (at rated load)
- On rear axle (at rated load)
DRAWBAR PULL ON THE COUPLING HOOK
- Unladen (slipping)
- At rated load (transmission setting)
DIMENSIONS
- A 1200 mm
- B 2300 mm
- C 991 mm
- D 3894 mm
- F 1492 mm
- I 603 mm
- U1 1920 mm
- U2 2054 mm
B
D
C
A
U1 U2
I
F
TECHNICAL CHARACTERISTICS
SWITCHES
A - Warning lights
B – Rear fog lights.
C - Rotating beacon light option
D - Front and rear working lights option
E - Option
F - Option
G - Neutralization of hydraulic movements
H - Option
I - Parkign brake
J - Disabling the "aggravating" hydraulic
movement cut-off
K - Attachment hydraulic locking option
L - Option
M - Option
N - Tiltig movement neutralization option
The location of the switches may
vary depending on the options.
M
N
L
J
K
B
D
F
H
A
C
E
G
I
4710 kg
7210 kg
2260 kg
2450 kg
6600 kg
610 kg
3080 daN
3450 daN
This device warns the operator of the longitudinal stability
limits of the forklift. Depending on the type of work
required, the longitudinal stability limiter and warning
device allows the operator to operate the lift truck in
complete safety.
The A8 LED indicates that the forklift truck is at the
authorized limit for longitudinal stability. If the light
comes on, perform smooth hydraulic movements.
"HANDLING" MODE (use with forks)
By default, the device is in "HANDLING" MODE when the
lift truck is started-up.
"BUCKET" MODE (use with bucket)
Press this button, "BUCKET" MODE is confirmed
by an audible beep and the lighting of the indicator lamp.
Press this button again to return to "HANDLING" MODE.
"SUSPENDED LOAD" MODE (use with hoist) (offering a higher margin of error)
Press this button, the "SUSPENDED LOAD" MODE is confirmed by a beep
and the lighting of the indicator lamp.
Press this button again or switch off the ignition with the ignition key to
return to "HANDLING" MODE.
A8
LONGITUDINAL STABILITY LIMITER AND WARNING DEVICE
