background image

035-000029-001

Page 1

HHA IOM 1.4  10/11/2021

How to Use this Manual:

This manual gives instructions regarding instal-
lation, operation and maintenance for the HHA 
Series air handling units.  For more information 
refer to:  

Catalog brochure

 for unit dimensions, op-

tions, guide specifications and performance 
information.   

New Magic 4

 software for faster selection 

of new equipment.  

Website 

www.magicaire.com

for replace-

ment parts guide, software downloads, 
product data and contact info for your local 
Magic Aire representative.  

Replacement Parts –

Identify parts need-

ed using the replacement parts guide avail-
able at 

www.magicaire.com

Use these instructions in conjunction with other 
appropriate instructions, including but not lim-
ited to those instructions supplied with the out-
door unit (if applicable).  Installation must com-
ply with all applicable local codes.  

GENERAL

Installation and maintenance are to be performed 

only

 by qualified personnel who are familiar with 

local codes and regulations and are experienced 
with HVAC equipment of this type.

WARNING:  Sharp edges, coil surfaces and 
rotating fans are a potential injury hazard –
avoid contact.  

WARNING:  Hazardous voltage – Discon-
nect and Lock Out all incoming power 
sources before servicing or installing unit.  
ELECTRIC SHOCK CAN CAUSE DEATH.

WARNING:  This equipment may be in-
stalled well above finished floor—Use ex-
treme caution when working at heights.  

SAFETY WARNING:

Installer should pay particular attention to the 
following words:

NOTE

–intended to clarify or make installation 

easier.  

CAUTION

–given to prevent equipment dam-

age.  

WARNING

–to alert installer that personal in-

jury and/or equipment damage may result if 
installation procedure is not properly followed.  

HHA Series 

Air Handler

Installation, Operation and Maintenance 

Manual

UNPACKING-CHECK FOR DAMAGE!

Immediately inspect each unit for damage up-
on receipt.  

 

Inspect units for external and concealed dam-
age immediately.

 

File any damage claims in accordance with 
Magic Aire Freight Damage Policy and Terms 
and Conditions (available at 

www.magicaire.com

).  

 

Do not repair damaged units without written 
authorization.  

 

Protect stored units from damage.  

DANGER

VFD Energy Stored!

Dangerous voltage is present when input power is 
connected.  After disconnecting power supply 
wait at least 5 minutes before performing any 
maintenance.

Magic Aire HHA Series units are 
direct drive High Static Horizontal 
Air Handlers delivering nominal 
airflows of 300 to 5000cfm and 
nominal cooling capacities of 1/2 
to 10 tons.  

  Units may be specified 

with chilled water or DX cooling coils 
and hot water or steam heating coils 
to meet space cooling loads or heat-
ing loads or both.  

Summary of Contents for HHA Series



































































Reviews: