48NDR
P. 1 / 8
EM-9443 Rev.5
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
BARGRAPH INDICATING ALARM
(with 4-digit digital meter; RTD input)
MODEL
48NDR
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■
PACKAGE INCLUDES:
Bargraph indicator (incl. scale plate) .......................... (1)
Mounting bracket ......................................................... (2)
Bezel*
1
........................................................................... (2)
Watertight packing ....................................................... (1)
*1. The size of included bezel differs depending on option code.
■
MODEL NO.
Confirm that the model number described on the product is
exactly what you ordered.
■
INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■
CONFORMITY WITH EC DIRECTIVES
• This equipment is suitable for Pollution Degree 2 and In
-
stallation Category II. Reinforced insulation (signal input
to output to power input: 300V) is maintained. Prior to
installation, check that the insulation class of this unit
satisfies the system requirements.
• The equipment must be mounted on a panel surface. Once
mounted on a panel, take appropriate precautions to pre-
vent operators to be exposed to the terminal block.
• Altitude up to 2000 meters
• Insert a noise filter for the power source connected to the
unit. TDK-Lambda Noise Filter Model MZS-1206-33 or
equivalent is recommended.
• The equipment must be installed such that appropriate
clearance and creepage distances are maintained to con-
form to CE requirements. Failure to observe these re
-
quirements may invalidate the CE conformance.
■
POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
AC rating: 85 – 264V, 50/60 Hz, approx. 5.5 – 8VA
DC rating: 24V ±15%, approx. 3.5W
■
ENVIRONMENT
• Indoor use
• If the unit’s environmental protection is compromised (e.g.
when multiple units are to be mounted side by side) when
heavy dust or metal particles are present in the air, install
them inside an enclosure with a proper ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■
REQUIREMENTS TO ENSURE IP65
• Observe the designated panel cutout size (31.5
×
138 mm).
• Single mounting only. IP65 is not ensured when the units
are clustered side by side.
• The watertight packing included in the product package
must be placed behind the front cover.
• The mounting bracket must be fastened tightly until they
hit the panel.
• Confirm visually that the packing is not contorted or ex
-
cessively run off the edge after installation.
■
WIRING
• Do not install cables (power supply, signal input and out
-
put) close to noise sources (high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■
TERMINAL BLOCK
• The terminal block is separable in two pieces. Loosen two
screws on top and bottom of the terminal block to sepa-
rate.
• Be sure to turn off the power supply, input signal and
power supply to the output relays before separating the
terminal block.
Terminal Block
Separable
Terminal Block Screw
(top & bottom)
■
AND ....
• The unit is designed to function as soon as power is sup
-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
