background image

Contents

Introduction

................................................................. 2

Front & Rear Panels - Fig. 1

....................... 4

Overview 

.......................................................................... 5

Channel Controls and Inputs  .................................................. 5

Channels 1 to 4  .................................................................... 5
Channels 1 and 2  ................................................................. 5
XLR Phantom Power  .......................................................... 5
EQ Controls .......................................................................... 5
Channels 5/6 and 7/8  ........................................................ 6
1/4” Inputs on Channels 5 to 10 ....................................... 6
Channels 9 and 10  ............................................................... 6
Tape In (RCAs)  .................................................................... 6
Send Controls  ...................................................................... 6

Stereo Return  ............................................................................. 7
Main Level Pot and LEDs  ......................................................... 7
Tape Out (RCAs)  ........................................................................ 7
Power Indicator and Switch  ..................................................... 7 

Typical Set-Up - Fig. 2 

........................................ 8

Setting-Up 

...................................................................... 9

Setting Up the Outputs   ............................................................ 9
Headphones............................................................................... 10

Applications and Hints 

................................... 10

Gain Settings ............................................................................. 10
Using the Send and Return for Effects .................................. 10

Block Diagram - Fig. 3 

...................................... 11

Limited Warranty 

.................................................. 12

MIXIM 10

™ 

M A N U A L

version: 

MXM10-072699

1

Summary of Contents for Mixim 10













Reviews: