10
o
90
o
60
o
30
o
BRACKET TOP VIEW
75MM (2.95IN)
2 X 8MM
12MM
DOME NUT
SPRING
WASHER
FLAT
WASHER
BRACKET
A
START
HERE
IMPORTANT INSTRUCTIONS
Lumascape Lighting Industries 2006
©
T 1-(650)-595-LUMA(5862) 1-(650)-595-5820
LUMASCAPE USA INC
Free Call 1-866-695-LUMA(5862)
C1714US - 2007_03_REV-001
t
90 C
t
90 C
A.C.N. 010 572 773
90
o
For Installation LS365: UNDERWATER
1
3
2
5C
MR16 LAMPS
9
MR16 LAMPS
5D
MR16 LAMPS
4
5B
PAR LAMPS
5A
PL LAMPS
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
instructions pertaining to a risk of fire, or injury to persons
WARNING
- To reduce the risk of FIRE or INJURY:
1.
Turn Off and allow to cool before replacing lamp.
2.
Lamp gets hot quickly! Contact only switch/plug when turning on.
3.
Do not touch hot lens, guard, or enclosure.
4.
Keep lamp away from materials that may burn.
5.
Do not touch the lamp at any time. Use a soft cloth. Oil from skin
may damage lamp.
DO NOT SHORTEN, INTERFERE OR DISCONNECT CABLE FROM FITTING. WARRANTY WILL BE VOID IF CABLE ASSEMBLY IS TAMPERED WITH.
If cable damaged replace with cable supplied by LUMASCAPE only.
WARNING
CAUTION - HOT BULBS. Keep Away From Curtains And Other Combustible Material.
140MM
(5.51IN)
80MM
(3.15IN)
160MM
(6.3IN)
Locate Fixtures
Site fixture in proximity to cabling. Use
discretion in locating fixtures as glass
can become very hot and may burn.
Mount Bracket to Fixture
Mount bracket supplied to fixture using the M10
dome nuts and washers as shown above.
Mount Fixture
Mount fixture to secure surface. Orientate
fixture as required and tighten nuts on bracket.
Connect Supply
Connect fixture to supply cable according to
local wiring rules.
Insert Lamp
Insert PL lamp into lampholder mounted on gear
tray in bottom of fixture. Insert reflector, locating
bottom into aluminium cup around lampholder.
Insert Lamp
Screw PAR38, or PAR30 lamp into
lampholder mounted on gear tray in bottom of
fixture. Ensure the lamp bottoms out in
lampholder.
Insert Lamp
Remove Hood and louvre from gimbal and
insert MR16 lamp into lampholder. Replace
hood and louvre.
SLIDE GIMBAL
VERTICALLY
GIMBAL
GIMBAL
LOCKING
SCREW
ALLEN KEY
SUPPLIED
ROTATE GIMBAL
Adjust vertical and rotational position of
gimbal
Rotate gimbal to aim light at target. Slide gimbal
vertically to minimise glare. Once positioned
tighten locking screw using Allen Key provided.
GIMBAL
ANGLE
ADJUST
SCREW
ALLEN KEY SUPPLIED
20
o
20
o
40
o
Adjust angular position of light
Aim the light at target by rotating the angle adjust
screw, with the Allen Key provided. The lamp has
a maximum adjust of 20 either side of vertical.
o
SEE OTHER SIDE FOR RE-LAMPING
www
.lumascape.com
Further
information
over page
LAMP
REFLECTOR
LAMP
GIMBAL
LAMP
HOOD/
LOUVRE
MODELS
IP68 rated
FOR UNDERWATER USE
LS365
INC.
Lumascape USA Inc.
1300 Industrial Rd., Unit #19
San Carlos, CA 94070, USA
T 1-(650)-595-LUMA(5862)
F 1-(650)-595-5820
E [email protected]
W www.lumascape.com
DISCONTINUED PRODUCT
