background image

1

 

StructureScan Installation

Accessories

If you received this manual with a StructureScan accessory, you will notice that 

some information in the document does not apply to the accessory. This manual has 

installation instructions for your accessory, and accessory pack content tables on the 

back cover. 

Contents

Your StructureScan box is packed with the LSS-1 black box, a Power cable, fuse 

and fuse holder, StructureScan transducer, mounting bracket, 15 foot (4.5m) ethernet 

cable and a hardware kit. The transducer has a 20 foot (6m) cable attached. 

Hardware Mounting Kit (Included)

             Transom mount screws (2)

            Transducer attachment lock  

             nuts (6)

             Bracket Assembly bolts (2)

             LSS-1 Mounting screws (4)

             Bracket Assembly washers (4)

        Closed end crimp connector (1)

             Bracket Assembly nuts (2)

Zip ties (2)

             Transducer attachment screws (6)

Required Tools and Supplies (Not Included)

Drill

Phillips (slotted-head) screwdriver

Drill bits

Marine grade above- or below- 

waterline sealant

LSS-1 module, ethernet cable, StructureScan transducer, transducer 

mounting bracket and power cable. 

Содержание StructureScan













Отзывы: