Lochinvar 140H Installation Manual And Owner'S Manual Download

Page: 1 / 76

Gas Tankless Water Heater

Suitable for combination potable water heating

and space heating. Please refer to local codes for

space-heating compliance.

On-Demand Water Heater

Installation Manual and Owner’s Guide

If you have any questions, please call

or write to:

In the United States

500 Tennessee Waltz Parkway

Ashland City, TN 37015

Toll Free: 1-877-737-2840

- Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

WARNING

If the information in these

instructions is not followed

exactly, a fire or explosion may

result causing property damage,

personal injury or death.

Keep this manual near the water heater for future reference whenever maintenance, adjustment, or

• COMPACT, SPACE SAVING

• ENERGY CONSERVATION

• COMPUTERIZED SAFETY

• NO PILOT LIGHT

• Complies with SCAQMD Rule

1146.2 for natural gas Low NOx

Emissions of 14 ng/J or 20 ppm.

CLICK ANYWHERE on THIS PAGE to RETURN to LOCHINVAR WATER HEATER INFORMATION at InspectApedia.com

Summary of Contents for 140H













































































Search results

Summary of Contents for 140H

Reviews:

Related manuals for 140H

Brands by name

Popular brands

Lochinvar 140H, Installation Manual And Owner'S Manual

Search results

Summary of Contents for 140H

Reviews:

Related manuals for 140H

Brands by name

Popular brands