little mule LMSC Series Operating, Maintenance & Parts Manual Download | Manualshive

Page: 1 / 16

background image

The use of any hoist presents some risk of
personal injury or property damage. That risk
is greatly increased if proper instructions and
warnings are not followed. Before using this
hoist, each operator should become
thoroughly familiar with all warnings,
instructions, and recommendations in this
manual. Retain this manual for future reference
and use.

Forward this manual to the hoist operator.

Failure to operate the equipment as directed
in the manual may cause injury.

Should you have any questions regarding this
product, please call Little Mule at

(800) 477-5003

.

Before using the hoist, fill in the information
below:

Model No.

Serial No.

Purchase Date

F

ollow all instructions and

warnings for inspecting, maintaining
and operating this hoist.

3/4 to 6 Ton

Model Numbers

LMSC1500
LMSC3000
LMSC6000

LMSC12000

Operating, Maintenance &

Parts Manual

LMSC680

LMSC

Series

Ratchet Lever

LMSC.qxd 7/11/2002 4:19 PM Page i

www.stlcrane.com

McLaughlin Hoist & Crane

(636) 343-9700

Authorized Sales & Service - McLaughlin Hoist & Crane - For Parts or Serivce Call (636) 343-9700

1
2
3
...
»

Summary of Contents for LMSC Series

















Reviews:

No comments

Related manuals for LMSC Series

Brand: Haklift Pages: 25

Brand: Ferm Pages: 44

DoNova PowerLash

Brand: Dolezych Pages: 23

DoLast Lever hoist DD Series

Brand: Dolezych Pages: 72

Brand: Beaver Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands