background image

DXT-54

WIRELESS
MOTION
DETECTOR

Installation Instructions

(619) 438-7000 

 FAX (619) 438-7043

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

PRODUCT DESCRIPTION

The DXT-54 is a battery powered passive infrared motion detector with
a built-in transmitter designed for use with Linear’s DX Format
receivers. This transmitter can be used in a variety of motion detection
applications. When the passive infrared sensor detects motion in its
field of view, the transmitter sends a digitally coded wireless signal to
its companion receiver.
The digital DX code format features over a million possible codes. The
DX transmitters are precoded at the factory to unique codes, so no field
coding is required. The DXT-54 can send two different codes: alarm
and low battery.
For versatility, 

any transmitter can be programmed into any receiver

channel.

 Receivers must be programmed to the transmitter’s code

before system testing and operation. Refer to the receiver’s
instructions for details on programming.
In a typical installation, the motion detector is mounted indoors in a
corner or on a wall between six and eight feet high. The sensor will
monitor the infrared level in its detection pattern. If the level increases
or decreases rapidly (as when a person or animal moves through the
area) the transmitter triggers, sending an alarm signal to the receiver.

The unit is powered from a 9-Volt alkaline battery with an expected
battery life of up to three years depending on the area’s traffic. When
the battery gets low, the test indicator will flash during motion and any
alarm transmission will also send a low battery signal to the receiver
(some receivers can report low battery, others cannot).
To conserve battery life, 

the detector will trigger the transmitter

only once every four minutes. 

When testing, remain out of the

detection area for at least five minutes before walking in front of the
unit to cause an alarm transmission.
For setup and testing, pressing the detector’s test button places the
unit in walk test mode for four minutes. The installer can walk in front
of the unit while viewing the test indicator behind the detector’s lens to
determine the detection area. In walk test, an alarm signal is sent each
time the walk test indicator lights.

DXT-54 FEATURES

DETECTION PATTERN

TYPICAL INSTALLATION

CONNECTING BATTERY

MOUNTING DETECTOR BASE

WALK TEST

PROGRAM RECEIVER AND TEST

CHANGING BATTERY

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The
Warranty Expiration Date is labeled on the product. 

This warranty extends only to wholesale customers

who buy direct from Linear or through Linear’s normal distribution channels. 

Linear does not warrant

this product to consumers. 

Consumers should inquire from their selling dealer as to the nature of the

dealer’s warranty, if any. 

There are no obligations or liabilities on the part of Linear corporation for

consequential damages arising out of or in connection with use or performance of this product or
other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,
installation, or reinstallation. 

All implied warranties, including implied warranties for merchantability and

implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. 

This

Linear Corporation Warranty is in lieu of all other warranties express or implied.

For warranty service on Linear equipment return product, at sender’s expense to:

Linear Corporation Repairs Department
2580 Pioneer Avenue, Suite C
Vista, CA 92083

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.

 

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as
Part 15 devices. As such, they have limited transmitter power and therefore limited range.

 

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by
radio signals that occur on or near their operating frequencies, regardless of code settings. 

 

Changes or modifications to the device may void FCC compliance.

 

Infrequently used radio links should be tested regularly to protect against undetected interference
or fault.

 

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
distributor or dealer, and these facts should be communicated to the ultimate users.

Copyright © 1995 Linear Corporation 

211690 A

BY

WALK
TEST
BUTTON

MOTION
DETECTOR
LENS

CASE
LOCKING
SCREW
(ON BOTTOM)

WALK TEST
INDICATOR
(BEHIND LENS)

DETECTION

AREA

30 FEET

30 FEET

30 FEET

6-8 FEET

SIDE

VIEW

TOP

VIEW

MOTION
DETECTOR
IN CORNER

DON'T POINT AT HEAT SOURCES 
(HEATERS, ETC.), WINDOWS, OTHER 
MOTION DETECTORS OR DOOR/WINDOW
TRANSMITTERS

BEDROOM

BATH

KITCHEN

FRONT
ROOM

(FOR INDOOR

USE ONLY)

MOUNT

DETECTOR

SO THAT

INTRUDER

WILL CROSS

BEAMS

MOTION
DETECTOR

REMOVE
SCREW
AND OPEN
CASE

CONNECT 9-VOLT ALKALINE
BATTERY TO BATTERY CLIP
(PLUS SIDE UP)

NOTE: BE SURE TO 
REPLACE THE CASE 
SCREW AFTER CLOSING 
THE CASE

PUNCH OUT REQUIRED HOLES
FOR SCREW MOUNTING

USE CENTER

HOLES FOR

WALL

MOUNTING

USE SIDE HOLES

FOR CORNER

MOUNTING

NOTE:

THE DETECTOR CAN
BE MOUNTED WITH
DOUBLE STICK TAPE,
BUT SCREW MOUNTING
IS PREFERRED

MOUNT
DETECTOR
6-8 FEET
HIGH

MOUNTING THE DETECTOR
IN A CORNER IS PREFERRED

AFTER MOUNTING, SNAP
DETECTOR ONTO BASE
AND REPLACE CASE SCREW

PUSH
WALK
TEST
BUTTON

WALK IN FRONT OF UNIT
WHILE WATCHING RED LIGHT

UNIT WILL STAY IN
WALK TEST MODE
FOR 4 MINUTES AFTER
PRESSING WALK TEST
BUTTON

VERIFY THAT DETECTION
PATTERN COVERS DESIRED
AREA

NOTE: AFTER INITIAL SETUP
WALK TEST UNIT ANNUALLY

AFTER PROGRAMMING RECEIVER
TO THE TRANSMITTER'S CODE
TEST THE SYSTEM

STAYING CLEAR, WAIT AT LEAST 
FIVE MINUTES BEFORE WALKING 
INTO THE DETECTION AREA

WALK ACROSS THE DETECTION
PATTERN AND VERIFY THAT
THE RECEIVER ACTIVATES

FOR PROGRAMMING,
REFER TO THE RECEIVER'S
INSTRUCTIONS

REMOVE
SCREW
AND OPEN
CASE

WHEN THE DETECTOR
HAS A LOW BATTERY:

REPLACE THE BATTERY WITH
A FRESH 9-VOLT ALKALINE
OR LITHIUM BATTERY
(PLUS SIDE UP)

USE ALKALINE
OR LITHIUM 
BATTERIES ONLY

SNAP DETECTOR ONTO BASE
AND REPLACE CASE SCREW
WHEN FINISHED

Reviews: