![background image](http://html.mh-extra.com/html/lightware/sw4-tps-tx240/sw4-tps-tx240_quick-start-manual_1915389001.webp)
Quick Start Guide
SW4-TPS-TX240
Further information
The document is valid with the following firmware version: 1.0.4
The User’s manual of this appliance is available at
www.lightware.com
.
See the
Downloads
section on the dedicated product page.
Contact us
+36 1 255 3800
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: 2.1
19200109
Important Safety Instructions
Please read the supplied safety instruction document before using the product and keep it
available for future reference.
Introduction
Thank you for choosing Lightware SW4-TPS-TX240 transmitter. The product has HDBaseT
TM
integration with additional Lightware developments. The device transmits DP / HDMI / DVI
digital video signal up to 4K resolution, audio and control up to 170 m distance over a single
CAT cable (DP signal is converted to HDMI).
Compatible Devices
The transmitters are compatible with other Lightware TPS
devices, matrix TPS and TPS2 boards, 25G boards, as
well as third-party HDBaseT
TM
extenders, displays, but not
compatible with the phased out TPS-90 extenders.
HDBaseT
TM
and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Box Contents
Front View
Rear View
Front Panel LEDs
Video Sources
OFF: video source is not selected.
BLINKING: video source is selected but not active.
ON: video source is selected and active.
Audio Sources
OFF: audio source is not selected.
BLINKING: audio source is selected but not active.
ON: (with short pause): audio source is selected and the port is active but not embedded
to the output video stream (DVI output mode).
ON: (continuously): audio source is selected, the port is active and the audio is embedded
to the output video stream (HDMI output mode).
When Autoselect is enabled and video signal is not present at all, video LEDs blink.
HDCP LED
OFF: video output signal is not encrypted with HDCP.
ON: video output signal is encrypted with HDCP.
Autoselect LED
OFF: autoselect is disabled.
BLINKING: autoselect is enabled; searching for signal (video LEDs also blink).
ON: autoselect is enabled; active video signal is found (the LED of selected video also
lights).
A port is active if a valid signal is detected.
Connecting Steps
Rear Panel LEDs
LIVE
OFF: device is not powered.
BLINKING (slow): device is powered and operational.
BLINKING (fast): device is in bootload mode.
ON: device is powered but no operation.
RS-232 LED
OFF: RS-232 ports (local and link) are in Pass-through mode.
BLINKING: command injection mode is active.
ON: RS-232 ports (local and link) are in Control mode.
SRVC
Reserved for future developments.
LINK
OFF: no TPS link between transmitter and receiver.
BLINKING (slow): low power mode is active.
BLINKING (fast): Ethernet fallback mode is active.
ON: TPS link is established, HDBaseT or Long Reach mode is active.
Transmitter unit
12V DC power adaptor
with interchangeable plugs
Infrared transmitter unit
Phoenix combicon
3-pole connector
Phoenix combicon
8-pole connector
Safety and warranty info,
Quick Start Guide
1
Autoselect LED
LED gives feedback about the HDCP status of the output
signal.
2
HDCP LED
LED gives feedback about the current Autoselect status.
3
DisplayPort Input
Input for DisplayPort audio/video signal. The applied cable
shall not be more, than 30 m (at 2.7 Gbps data speed).
4
HDMI Inputs
HDMI connectors for DVI video or HDMI video and audio.
5
DVI-D input
DVI-I connector for DVI-D video and audio.
6
Audio input
3.5 mm Jack connector for asymmetric analog audio signal.
7
Video/Audio Select
Selecting a video/audio input manually.
8
Reset Button
Pushing the button reboots the unit.
9
Show me Button
Special functions are available with this button (e.g. enable
DHCP or restore factory default settings).
1
HDMI output
Local HDMI output with the same A/V content as the TPS
output.
2
TPS output
Locking RJ45 connector for HDBaseT
TM
signal transmission.
3
Ethernet
Locking RJ45 connector for Ethernet communication.
4
Status LEDs
The LEDs give feedback about the actual state of the device.
5
IR in and out
2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter).
6
GPIO port
8-pole Phoenix connector for configurable general purpose
input/output ports.
7
RS-232 port
3-pole Phoenix connector for RS-232 serial port.
8
12V DC input
connector
12V DC input for local powering.
Power Supply Options
The transmitter can be powered:
Locally with the supplied 12V DC adaptor or Lightware’s rack mountable PSU, or
Remotely by a PoE-compatible power injector, like Lightware’s TPS-PI-1P1.
Powering by a matrix board over the TPS (CATx) cable. Output board needs to be
powered by an external PSU.
SW4-TPS-TX240 transmitter is PoE-compatible and can receive power over the TPS line.
The TPS-TX/RX95 extenders are not PoE-compatible thus not able to send/receive power to/
from the SW4-TPS-TW240 transmitter.
CATx
DVI
Connect the TPS output port to the receiver (or the Matrix input board) by a
CATx cable via the
TPS output
port.
HDMI
DP
DVI-I
C
onnect the transmitter and the sources using the inputs and VGA /
DisplayPort / HDMI / DVI-I / cables.
Audio
Optionally for audio extension: connect the audio source (e.g. media player)
to the audio input port by an audio cable.
LAN
Optionally connect the transmitter to a LAN in order to control the device.
GPIO
Optionally connect a controller/controlled device (e.g. relay box) to the
GPIO port.
RS-232
Optionally connect a serial device to the RS-232 port of the transmitter.
IR
Optionally for Infrared extension:
Connect the IR emitter to the IR OUT port of the transmitter, and/or
Connect the IR detector to the IR IN port of the transmitter.
Power
Powering on the devices is recommended to do as the final step during the
installation. Please see the
Power Supply Options
section for the details.
Locking DC plug
Twist 90° clockwise to lock.
Mounting
To mount the device Lightware supplies optional accessories for different usage. There are
two kinds of mounting kits with similar fixing method. The transmitter has two mounting holes
with inner thread on the bottom side. Fasten the device by the screws enclosed with the
accessory.
The Under-desk double mounting kit makes it easy to mount a single device on any flat
surface, e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half-rack
or four quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To
order mounting accessories please contact
.
Using different (e.g. longer) screws may cause damage to the device.
The transmitter is half-rack sized.
Under-desk double mounting kit
1U high rack shelf
2
3
4
5
7
7
1
6
8
9
1
2 3 4
6
5
8
7
Safety and
Warranty
Info
Quick
Start
Guide
MX-
TPS2-
IB-P
DC
IN
8 CH
TPS
INPU
T BOA
RD
WITH P
OE
48V
5A
-
+
Ethe
rnet
TPS IN 1
TPS
IN 2
TPS I
N 3
TPS I
N 4
8CH INPUT
BO
ARD
FOR HDM
I WI
TH 3
D AND
ANAL
OG
AUDIO
MX-HDMI
-3D-IB-A
IN 1
IN 2
IN 3
IN 4
MX-
TPS2-
OB-
S
48V
5A
DC
IN
8 CH
TPS
OUTP
UT
BOARD
WITH
DIGIT
AL
AUD
IO
12V
power
on TP
S connec
tor.
Only use wi
th c
ompat
ible
devi
ces!
12V
power
on TP
S connec
tor.
Only use wi
th c
ompat
ible
devi
ces!
TPS
OUT
1
TPS
OUT
2
TPS
OUT
3
TPS
OUT
4
8CH O
UTPUT
BOARD
FOR
HDMI WIT
H 3D
AND
ANAL
OG
AUDIO
MX-HDMI
-3D
-OB-A
OUT
1
PIN: 2.1mm
RS-232
TX R
X
12V 1A
DC
TPS-PI-1P1
48 DC
IN
Typi
cal:
0.7
A
Max
: 1.5
A
- +
Max:2.
5A
m
m2 :
NI
P
CATx
(TPS)
Power
send
48V DC
Power
adaptor
12V DC
Power
adaptor
CATx
(TPS)
External
power supply
Power
send
PIN:
2.1mm
RS-
232
TX RX
IR IN
IR OUT
LIVE
RS-
232
SRVC
LINK
12V
1A
DC
TPS
OUT
(Po
E)
GPIO
1 2
3
4
5 6
7
HDMI O
UT
PIN:
2.1mm
RS-
232
TX RX
IR IN
IR OUT
LIVE
RS-
232
SRVC
LINK
12V
1A
DC
TPS
OUT
(Po
E)
GPIO
1 2
3
4
5 6
7
HDMI O
UT
PIN:
2.1mm
RS-
232
TX RX
IR IN
IR OUT
LIVE
RS-
232
SRVC
LINK
12V
1A
DC
TPS
OUT (P
oE)
GPIO
1 2
3
4
5 6
7
HDMI O
UT
Power
RS-232
GPIO
IR
Ethernet
Infrared
Relay box
LAN
Compatible
TPS Receiver
Touch panel
SW4-TPS-TX240
CATx
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
AUDIO
VIDEO
AUDIO
RESET
Autoselect
HDCP
AUDIO
DP IN
HDMI IN
HDMI IN
DVI-D IN
AUDIO IN
5
Audio
DVI-I
Blu-ray player
HDMI
DP
Mac
Media player
PC