Quick Start Guide
FP-HDMI-TPS-RX97-GB3
WP-HDMI-TPS-RX97
Further Information
The product brief and further information of this appliance is available at
section on the on the dedicated product page.
Contact us
+36 1 255 3800
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: 2.0
19200172
Important Safety Instructions
Please read the supplied safety instruction document before using the product and keep it
available for future reference.
Introduction
WP/FP-HDMI-TPS-RX97 series twisted pair HDBaseT
TM
extenders provide extension of
uncompressed 4K/UHD video with embedded audio (up to eight channel PCM or HBR audio)
for long distances over a single CATx cable.
Box Contents
Receiver unit
UNC 6-32 bright zinc plated
pan head screws (4x) *
Safety and Warranty info,
Quick Start Guide
Phoenix
®
Combicon
3-pole connector
1
Status LEDs
The LEDs give feedback about the state of the unit and the video
signals.
SIGNAL
off
No video signal transmission.
on (green)
Video signal transmission is active.
LINK
off
TPS connection failed between the
extenders.
blinking
(green)
TPS connection is detected and Low
Power Partial Functionality (LPPF) link
mode is active.
on (green)
TPS connection is detected and
HDBaseT
TM
(HDBT) or Long reach (LR)
link mode is active.
LIVE
off
Device is not powered.
blinking
(green)
Device is powered and ready to use.
2
IR input/output
2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter).
3
RS-232 connector
3-pole Phoenix connector for RS-232 serial port. Firmware
upgrade can also be performed over this interface.
4
Ethernet
Locking RJ45 connector for Ethernet communication.
5
HDMI output
HDMI output for DVI or HDMI signal. Connect an HDMI cable
between the receiver and the display device.
6
DC Input
Connect the output to the 2-pole Phoenix connector on the
bottom of the wall plate.
7
TPS input
Locking RJ45 connector for HDBaseT
TM
signal transmission.
Connect a twisted pair cable between the transmitter and the
receiver.
8
RS-232 switch
Normal:
serial data is passed through the device.
Prog:
RS-232 pass-through function is disabled, the device
is ready for the firmware upgrade (see RS-232 switch modes
section for details).
9
TPS mode switch
LR:
Longreach TPS mode; lower resolution (max 1080p),
longer distances.
Auto:
TPS mode is determined automatically.
q
Tie-down point
The built-in tie-down points are designed to clamp the
HDMI and the CATx cable and ensure stable connection.
Please see the enlarged picture below.
Rear View (WP-HDMI-TPS-RX97 assembled with FP-8AT plate)
Front View (WP-HDMI-TPS-RX97 assembled with FP-8AT plate)
Connecting Steps
Bottom View (WP-HDMI-TPS-RX97 assembled with FP-8AT plate)
RS-232 Switch Modes
Please note that the 48V power adaptor is
an optional accessory which can be purchased
separately.
* For WP-HDMI-TPS FP-8AT front plate only.
CATx
DVI
Connect the TPS input port of the receiver to the
TPS+PoE
port of the
TPS-PI-1P1 by a CATx cable.
Connect the receiver (or the matrix output board) to the power injector by a
CATx cable via the TPS port.
HDMI
Connect the sink (e.g. Projector) to the HDMI output port by HDMI cable.
RS-232
Optionally for RS-232 extension: connect a controller/controlled device (e.g.
Projector) to the RS-232 port.
IR
Optionally for Infrared extension:
Connect the IR emitter to the IR OUT port of the receiver, and/or
Connect the IR detector to the IR IN port of the receiver.
LAN
Optionally connect the receiver to a LAN.
Power
Powering on the devices is recommended to do as the final step during the
installation. Please check the
Power Supply Options
section for the details.
The product is compatible with any HDBaseT
TM
third party devices.
HDBaseT
TM
and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Power Supply Options
TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -
and can receive power over the TPS line.
The extender can be powered by any of the following ways:
1. Local adaptor
2. Remote power injector
3. Matrix board
TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power
the WP/FP-HDMI-TPS-RX97 series and vica versa. WP/FP-UMX-TPS-RX97 series contains
PoE-compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can
be remote powered only by each other.
¢
Warranty void if damage occurs due to the usage of a different power source.
Compatible Devices
TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90
series.
HDMI
Compatible
transmitter or
matrix output
board
WP-HDMI-TPS-RX97
Power adaptor
IR detector Ethernet
Projector
Power
LAN
RS-232
IR
WP-HDMI-TPS-RX97-US
HDMI OUT
Ethernet
TPS-PI-1P1
Power injector
CATx
CATx
48V DC
Power
adaptor
TPS-PI-1P1
CATx
(TPS)
Power
send
48V DC
Power
adaptor
MX-
TPS2-
IB-P
DC IN
8 CH
TPS
INPUT
BOARD
WITH
POE
48V
5A
-
+
Ethernet
TPS IN
1 TPS IN
2 TPS IN 3
TPS IN 4
8CH I
NPUT
BO
ARD F
OR HDMI
WIT
H 3D
AND
ANALO
G AUDI
O
MX-HDMI-3D-IB-A
IN 1
IN 2
IN 3
IN 4
MX-
TPS2-
OB-
S
48V
5A
DC
IN
8 CH
TPS
OUTPUT
BOARD
WITH
DIGI
TAL
AUDI
O
12V
power
on TPS
connect
or. Onl
y use
with
compat
ible
devi
ces!
12V
power
on TPS
connect
or. Onl
y use
with
compat
ible
devi
ces!
TPS O
UT 1
TPS OUT 2
TPS O
UT 3
TPS O
UT 4
8CH O
UTPUT
BOARD F
OR HDMI W
ITH
3D AND
ANAL
OG
AUDIO
MX-HDMI-3D-O
B-A OUT
1
OUT
2
OUT
3
CATx
(TPS)
External
power supply
Power send
Typi
cal:
0.5A
Max:
1.25A
- +
Max:2.5A
m
m2 :
NI
P
IR OUT
IR IN
LINK
TX
RX
LIVE
SIGNAL
WP-HDMI-T
PS-RX97-US
H
D
M
I O
U
T
E
thernet
IR OUT
IR IN
LINK
TX
RX
LIVE
SIGNAL
WP-HDMI-T
PS-RX97-US
H
D
M
I O
U
T
E
thernet
IR OUT
IR IN
LINK
TX
RX
LIVE
SIGNAL
WP-HDMI-T
PS-RX97-US
H
D
M
I O
U
T
E
thernet
RS-232
TPS port
Programming
Switch
normal
prog
4
5
7
6
1
2 3
1
q
Safety and
Warranty
Info
Quick
Start
Guide
IR IN
SIGNAL
HDMI OU
T
8
9 6
