Light Beam Antenna LBM-17M+20M Скачать руководство пользователя

Страница: 1 / 26

The Light Beam Multi-band Antenna

Model LBM - 17M+20M

Installation Instructions

Light Beam Multi-band Antenna Series

Model: LBM-17M+20M

W. A. Freiert – WB2LYL

The Light Beam Multi-band antenna is a compact, computer optimized, directional antenna with good gain and

excellent front to back ratio. The antenna has been optimized for operation at 30 ft above the ground.

Please read these Installation Instructions completely

before beginning installation of your antenna.

Check Your Delivery

Your Light Beam antenna has been shipped in one (1) box. Carefully

inspect the packaging for damage then unpack the antenna and note any

shipping damage. If any damage is found, contact the shipping carrier for

insurance coverage.

Parts Photographs

Boom Components

Quantity

1.5” OD x 48” Tube

1.5” OD x 24” Tube

1.25” OD x 36” Tube

1.25” OD 0.058” x 36” Al. Tube

Note 1 1.125” OD 0.058” x 36” Al. Tube 2

1.0” OD x 48” Tube

1.0” OD 0.058” x 36” Al. Tube

0.75” OD x 12” Tube

0.5” OD x 12” Rod

Note 2 3/4”copper to 1/2” Elbow

Fig. 1

Note 1:

The 1.125” Aluminum Tube is within the

1.250” Aluminum Tube.

Note 2:

The Elbows and associated hardware

are pre-assembled in the 1.25” x 36” Fiberglass

Tubes.

Boom Components

Содержание LBM-17M+20M



























Результаты поиска

Содержание LBM-17M+20M

Отзывы:

Похожие инструкции для LBM-17M+20M

Бренды по названию

Популярные бренды

Light Beam Antenna LBM-17M+20M, Руководство по установке

Результаты поиска

Содержание LBM-17M+20M

Отзывы:

Похожие инструкции для LBM-17M+20M

Бренды по названию

Популярные бренды