LEN.MAN.UPS.169 Rev.3.00/2013
SPECIFICATION
SAFETY INSTRUCTIONS
Please read carefully and follow this UPS guide and keep this user's guide
for reference in order to use the UPS properly and safety. This user's guide
contains instructions for installation, preservation, operation and
specification.
For product safety, please check this product annually by our service
qualified personnel or if there are any symptoms of problems which are not
mentioned in this guide or an queries, please contact your local distributors
or service center.
Warning
Risk of electric shock, DO NOT remove cover. No user serviceable
part inside, please refer servicing to qualified service personnel.
1. Electrical Safety
1.1 Do not work alone under hazardous condition.
1.2 Contact with live conductors will cause burns and dangerous electric
shock.
1.3 Periodically check your cables, outlets and power source to make sure
that they are in good condition.
1.4 To reduce the risk of electric shock if you cannot find the electrical
ground ( ) of building, unplug UPS from AC source before plug in
your loads at the rear side of the UPS. Then, plug in the UPS to AC
source.
1.5 Do not touch any metal parts or any electrical connections when UPS is
operating.
1.6 Use ONLY one hand when plugging and unplugging the load in order
to avoid electric shock from touching surfaces with different potential.
1.7 It is recommended to connect UPS to a three wire AC source (two live
wires and ground) which connect to a protected circuit such as fuse or
circuit
breaker.
2. CAUTION! Safety instructions for installation and operation
2.1 Before installing or using this UPS, read all instructions, caution making
on UPS and all connected loads, and all sections of this user's guide.
2.2 Install UPS in a temperature and humidity controlled indoor area with
sufficient ventilation and away from dust, chemical particles or
flammable substances. Avoid installing UPS in areas near radio
transmission station, heat dissipation equipment or direct sunlight.
2.3 UPS has ventilation grills on the sides. Ensure that sufficient ventilation
is provided, do not block the ventilation grills. The distance of
minimum 30 cm between wall and unit is necessary.
2.4 Use insulated tools to reduce the risk of electric shock.
2.5 Remove all ornaments or other metal objects such as rings, necklaces,
bracelets and watches before installing.
2.6 Before connecting the communication interface signal cable to
computer, turn off UPS and disconnect it from AC source.
2.7 Turn on UPS before turning on connected loads to prevent surge from
the
loads.
2.8 Do not connect AC source input to UPS output. This may cause UPS
damage.
2.9 When heavy rain, avoid using electronic equipments including UPS to
prevent them from lightning.
2.10 Do not clean UPS with benzene, thinner or any solvent, use only soft
cloth to clean UPS after it has been turned off.
2.11 Do not use the UPS with life recovery instruments. The failure of UPS
may cause life recovery instruments failure or effect to their
performance or the safety system of those instruments.
3. Warning! Battery Safety
3.1 Although UPS is disconnected to any power source, UPS outlets may
be energized because there is a battery inside the UPS.
3.2 The UPS has hazardous voltage inside, do not dissemble any parts of
UPS. Battery replacement must be done by Leonics qualified
technicians
only.
3.3 The batteries inside UPS can be recycled. It contains lead which is
harmful to your health and environment. If it cannot be disposed
of properly, please return it to local distributors or Leonics Service
Center.
3.4 Do not dispose batteries with fire, they will be exploded.
3.5 Do not disassemble batteries. They contain poisonous electrolyte
which is harmful to your skin and eyes.
3.6 Replace batteries with the same type and rating.
U S E R ' S G U I D E
■
www.leonics.com
■
MICROPROCESSOR CONTROL AND
LINE INTERACTIVE UPS WITH STABILIZER
(1)
Pentium 4, 1.8 GHz chip computer with monitor 15",
(2)
Bubble jet or dot matrix printer,
(3)
Easy-Mon V Software compatible with
Windows 98/2000/2003/XP/Vista X/2008/Windows 7, Redhat Linux 8/Redhat enterprise AS3/Suse Linux 10/Ubuntu 6.10/Fedora 5,
Solaris 10, Mac OS X/10.3/10.4/10.5.
Continuous product development is our commitment. In that manner, the above specifications may be changed without prior notice.
UPS system
Control system
Stabilizer function
The number of PC
(1)
Input voltage
Frequency
Voltage battery mode
Voltage AC mode
Over voltage
Under voltage
Transfer time
Overload (AC mode)
Overload (DC mode)
Overload shortcircuit
Surge energy dissipation
Power dissipation
Acoustic noise
Type
Capacity
Backup time
Continuous recharging time
Number of backup outlet
Number of surge protection outlet
(not backup)
AC/DC start
Communication interface
Monitoring and Management
Software
Surge protection for telephone line
Surge protection for LAN line
Surge protection for laser printer
LCD display
Battery mode
Low battery
Overload
Battery replacement
Fault
Temperature
Humidity
W x H x D (mm.)
Approximate in kg.
MODEL
POWER RATING
SYSTEM
LOAD APPLICATION
INPUT
OUTPUT
PROTECTION
BATTERY
OUTPUT OUTLET
FEATURE
INDICATOR
AUDIBLE ALARM
(BUZZER)
ENVIRONMENT
DIMENSION
WEIGHT
OA-650 OA-750 OA-1100 OA-1600
650 VA/390W 750VA/450W 1100VA / 605W 1600VA / 960W
Line interactive UPS with Stabilizer
Microprocessor 8 bit
Buck / Boost
1 set+printer
(2)
2 sets+printer
(2)
3 sets+printer
(2)
4 sets+printer
(2)
220 Vac ± 20%
50 Hz ± 10%
220
Vac
220 Vac ± 10%
Mains to UPS backup 220 Vac + 20%
Mains to UPS backup 220 Vac - 20%
2 - 6 msec. typical, 10 msec. maximum
yes
yes
software
detection
125 Joules / 2 ms. x 3
1,000,000 W within 100 microsec.
Less than 40 dBA at 1 metre
Sealed lead acid (maintenance free)
1 x 12 V 7 Ah 1 x 12 V High Rate 2 x 12 V 7 Ah 2 x 12 V High Rate
15 - 40 min. (depending on connected load)
4 to 6 hours (90% after full discharged)
3
5 6
1
1 2
yes
USB
port
Easy-Mon V software
(3)
yes
no
option
yes
AC mode, Battery mode, Load level, Battery level, Input
voltage, Output voltage, Overload, Fault, and Low battery
Audible beep every 10 seconds
Audible beep every second
Audible beep every 0.5 seconds
Audible beep every 2 seconds
(Battery test function on Easy-Mon V software)
Continuous
beep
0 - 40˚C
0 - 90% (non-condensing)
100 x142 x 287 100 x 142 x328 146 x 160 x 350 146 x 205 x 397
4.45
4.81
8.0
11.5
