Lenz Elektronik Digital Plus Manual Download

Page: 1 / 13

Silver Direct Locomotive decoder

The DIGITAL plus SILVER locomotive decoder has a built in NMRA 8 pin plug and is suitable for
all DC locomotives with continuous current draw of 1.0 Amp. or less. That have a DCC Medium
plug socket. The characteristics of the decoder are:

∗

Super smooth and silent high frequency back-emf motor control.

∗

Asymmetrical DCC support including directional stopping.

∗

Adjustable precision stopping control.

∗

Low speed gear for switching operations.

∗

Selectable for operation with 14/27, or 28/128 speed steps.

∗

Operation on conventional DC layouts is possible or can be disabled.

∗

Motor output = 1A continuous, 1.8A max, > 5 A stall.

∗

Motor and function outputs protected.

∗

Four function outputs rated at 100mA each with advanced function mapping.

∗

Directional or independent lighting with dimming and special effects.

∗

Support for Advanced Consist Control and Extended Addressing.

∗

Support for programming on the mainline (operations mode programming).

∗

Support for all form of programming as described in NMRA RP-9.2.3

∗

Supports service mode decoder lock.

∗

Size: L 0.71" x W 0.50"x H 0.14" L 18mm x W 12.9 mm x H 3.6mm

Silver Direct Silent
Back EMF DCC Decoder

Art. No.

10330

February 2007

Core software based on

NMRA Conforming

Silver MP Decoder

Summary of Contents for Digital Plus














Search results

Summary of Contents for Digital Plus

Reviews:

Related manuals for Digital Plus

Brands by name

Popular brands

Lenz Elektronik Digital Plus, Manual

Search results

Summary of Contents for Digital Plus

Reviews:

Related manuals for Digital Plus

Brands by name

Popular brands