background image

SERVICE

G20RE

UNIT

INFORMATION

Page 1

 1994 Lennox Industries Inc.

Corp. 9419 – L9

Litho U.S.A.

G20RE SERIES UNITS

I – INTRODUCTION

G20RE and G20RXE series units are mid–efficiency
downflow gas furnaces with Duracurve

  heat ex-

changers formed of  aluminized steel. G20RE units
come in heating capacities of 50,000 to 150,000 Btuh. In
cooling applications, blowers are equipped to handle
up to 5 tons of cooling capacity. Refer to Engineering
Handbook for proper sizing.

Units are factory supplied for use with natural gas. A
conversion kit to LPG operation is available for the
G20RE only. All units are equipped with an electronic
ignition. G20RXE models meet the California Nitrogen
Oxides (NO

x

) Standards and California Seasonal Effi-

ciency requirements. All units use a redundant gas
valve to assure safety shut–off as required by A.G.A.

Featured on G20RE series is a burner box damper as-
sembly located on the intake side of the burners. A
damper door in the burner box shuts during unit off
cycles to retain heat in the unit. A damper prove switch
ensures that damper is open before gas valve is ener-
gized. Since the G20RE furnaces have atmospheric
burners there is no induced draft motor. All G20RE
units have a draft diverter which allows the use of stan-
dard single wall vent connectors.

SPECIFICATIONS 

(continued on next page)

Model No.

Input Btuh
Output Btuh
*A.F.U.E.

Flue connection (in. diameter)

Temperature rise range
High static certified by A.G.A.(in wg.)

Gas piping size

I.P.S. (in.)

Blower wheel nominal diameter x width (in.)

Blower motor hp.

Electrical characteristics

Natural

**

LPG

G20RQ2/3E-50

G20RQ3E–75

G20RQ4E-75

G20RQ3/4E-100

50,000
40,000

78.0%

4 Round

20-50

.50
1/2

1/2

10 x 8

1/3

2, 2–1/2 or 3

Tons of cooling (add–on)

58,000

78.0%

78.0%

78.0%

75,000

59,000

75,000

79,000

4 Round

4 Round

5 Oval

50-80

30-60

50-80

.50

.50

.50

1/2

1/2

1/2

1/2

1/2

1/2

10 x 8

11 x 9

11 x 9

1/3

1/2

1/2

*Annual Fuel Utilization Efficiency based on D.O.E. test procedures and according to F.T.C. labeling requirements. 
 Isolated combustion system rating for non–weatherized furnaces.

G20RQ2/3XE-50

G20RQ3XE–75

G20RQ4XE-75

G20RQ3/4XE-100

100,000

California Seasonal Efficiency– “X” Models

72.1%

74.8%

72.0%

74.5%

Number and Size of Filters (in.)

(2) 20 x 10 x 1

(2) 20 x 10 x 1

(2) 20 x 12 x 1

(2) 20 x 12 x 1

2, 2–1/2 or 3

3, 3–1/2 or 4

3, 3–1/2 or 4

Not Available with LPG.

**LPG kit must be ordered extra for field changeover.

120 volts — 60 hertz — 1 phase (less than 12 amps) — All Models

Summary of Contents for G20RE Series















Reviews: