background image

FOR QUALIFIED INSTALLER ONLY.

 This basic Installation Sheet is an initial release. If a complete Operations  

Manual (for the unit being installed) is required or needed, please refer to the Lancer Corp website (lancercorp.

com) or for your convenience, scan this QR code with a mobile device (app required) for immediate access to other     

Technical Documents and alternative translations (if available) pertaining to this unit. Contact Lancer Customer    

Service for any assistance.

ABOUT THIS MANUAL

This booklet is an integral and essential part of the product and 

should be handed over to the operator after the installation and 

preserved for any further consultation that may be necessary. 

Please read carefully the guidelines and warnings contained 

herein as they are intended to provide the user with essential 

information for the continued safe use and maintenance of the 

product. In addition, it provides 

GUIDANCE ONLY

 to the user on 

the correct services and site location of the unit.

BEFORE GETTING STARTED

Each unit is tested under operating conditions and is thoroughly 

inspected  before  shipment.  At  the  time  of  shipment,  the  carrier                               

accepts responsibility for the unit. Upon receiving the unit,     

carefully inspect the carton for visible damage. If damage exists, 

have the carrier note the damage on the freight bill and file a 

claim with carrier. Responsibility for damage to the dispenser lies 

with the carrier.

IMPORTANT SAFETY INSTRUCTIONS

The installation and relocation, if necessary, of this product must be carried out by qualified personnel with 

up-to-date safety and hygiene knowledge and practical experience, in accordance with current regulations.

310

LANCER PN: 28-0827/04

The dispenser is for indoor use only. This appliance is to be installed in a location where its use can be overseen by trained 

personnel. This unit is not a toy. Children should be supervised not to play with appliance. It should not be used by children or 

infirm persons without supervision. This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible for their safety. Cleaning and user maintenance shall not be performed by 

children without supervision. The min/max ambient operating temperature for the dispenser is 4°C to 41°C (40°F to 105°F). Do not 

operate unit below minimum ambient operation conditions. Should freezing occur, cease operation of the unit and contact 

authorized service technician. Service, cleaning and sanitizing should be accomplished only by trained personnel. Applicable safety 

precautions must be observed. Instruction warnings on the product being used must be followed.

Intended Use

UNICORN TOWER

LANCER INSTALLATION GUIDE

Summary of Contents for UNICORN TOWER













Reviews: