Interface Lead Item nr. 67725X719 for
Opel / Vauxhall with Quadlock connector.
Including AUX connection for Music.
Product Description
The Interface leads range allows connection of Aftermarket carkits to OEM Phone preparation.
Interface Leads
are used when installing aftermarket telephone carkits. It is used for car stereos with a Phone
Line-In function or VDA preparation. It enables the use of the car speakers when answering/making calls from
your cell phone. For a complete cable-set two item no. are required. The first is a car-specific Interface Lead.
The second is a carkit-specific Interface adaptor cable .
Speaker-function: This is achieved by connecting the carkit directly to the cars Line-In input/VDA connector. By
using the radios built-in switch function the telephone conversation is heard through the car speakers while the
radio sound is muted. This way you will achieve a perfect hands free sound without interference from the car
radio.
Power supply of the carkit: All Interface Leads are delivered with power and ground from the car connector
connected to the carkit, this way cutting the cars wiring loom is avoided.
Ignition supply: If an ignition source is available in the radio/VDA connector then it is also available in the 16
pin connector. If an ignition source is not available a constant 12V source is connected to the Ignition pin via
bullet connectors. If a real ignition is required for the chosen carkit, an IGNIBOX item no. “I” can be connected
to create an artificial ignition or an ignition source found elsewhere can be connected to the bullet with the
blue wire. The 12V ignition wires in the Interface leads are blue.
Aux integration
Some Interface leads have the radio AUX input available in a 4 pin connector. This will allow the use of the car
sound system amplifier for Music playback when installing Music carkits and thereby achieving higher audio
quality.
EN725-V1
Troubleshooting Guide
Carkit does not start up.
Check if there is 12V between the black and the red wire and also between the black
and blue wire, in the 16 pin connector, when the car is started. If there is not 12v on both wires please check
the following:
1.
If there is supply on the red constant 12v wire but not on the blue ignition wire the car may require an
alternative ignition source. See installation step 5.
2.
Check that the bullets on the supply wires are properly connected. The supply wires are the red, blue
and black wires.
3.
Check for a blown fuse on the Interface Lead or in the cars fuse-box.
The carkit does not turn off.
1.
Please make sure the key is removed from the ignition barrel. On many new cars ignition is not turned
off until the key is pulled out.
2.
Is there an ignition supply on the blue wire? There should be no voltage on the blue wire when there
is no key in the ignition. See installation step 4.
Speakers are not muted.
1.
Check that the mute wire is connected to the right position. See installation step 3.
2.
Locate the radio instruction manual and check for special menu settings regarding phone input.
3.
Please check that there is close to 0V on the yellow mute wire during a call. If there are more than
approximately 0V the carkit may be defective please try another carkit.
Speakers are muted but there are no carkit sound.
1.
Please check that the carkit and radio volume is turned up.
2.
Locate the radio instruction manual and check for special menu settings regarding phone input.
3.
The carkit may be defective. Please try another carkit.
Radio will not turn on or not working properly after installation.
1.
Please check for a blown fuse at the back of the radio or in the car fuse-box.
2.
Please check that all connectors are properly connected and that there are no bend or damaged pins.
3.
Remove the Interface Lead and connect the radio to the original car connector. If the radio is now
working replace the Interface Lead.
Volume to high or sound is disordered.
1.
Please try to turn down the carkit volume and turn up the volume using the radio volume control in-
stead. If the carkit volume has to be turned almost completely down improved adjustment range can
be achieved by connecting a inline resistor item number: 68897 inline with the white wire to limit the
carkit output.
2.
There may be a Ground loop problem when combining this exact carkit and radio model. Please try to
insert Ground loop isolator item number: 69897 inline with the white and white/black wires from the
carkit.
Technical Specifications
Description:
L-shaped with bullet connections for Ground, Constant 12v and Ignition.
Normal Wire dimensions :
AWG 18 for power wires, AWG 20 for all other wires
Standard Fuse sizes:
3 Amp for constant supply, 1 Amp for Ignition supply
Maximum Fuse size:
7,5 Amp for constant supply, 7,5 Amp for Ignition supply
Size:
400 x 400 mm
Configuration chart for 16 pin connector:
Connector seen from cable entry side
12V
Const.
12V
IGN
Carkit
RF+
Carkit
LF+
GND
Mute
Out
Mute
In
Carkit
RF-
Carkit
LF-
Interface Leads
Interface Leads
