GETTING STARTED: REVIEW BEFORE BEGINNING INSTALLATION
SAVE THESE AND ALL INSTRUCTIONS! For more details and additional important information, see the other instructions provided inside your refrigerator.
W11127202B
©2017. All rights reserved.
06/17
IMPORTANT
INSTALLATION CHECKLIST
✔
Electrical Power
❑
Plug refrigerator into a grounded 3 prong outlet.
✔
Doors
❑
If doors need to be removed during installation,
see the “Remove and Replace Doors” section in
the instructions.
❑
Check that handles are secure and installed according
to the instructions.
❑
Doors seal completely.
❑
Refrigerator is level. (Remove base grille and adjust leveling
feet so they are snug against the floor.)
❑
Doors are even across the top. (Use door alignment feature
if necessary.)
❑
Base grille is properly attached to the refrigerator.
✔
Ice and Water System (on some models)
❑
Connect refrigerator to a cold water supply with 20-120 psi
water pressure, as specified in the instructions.
❑
Make sure the household water supply is connected and
turned on.
❑
Check that the water supply line behind refrigerator
is not kinked.
❑
Only use recommended water supply tubing, copper, or
PEX, as specified in the instructions.
❑
Install water filter according to the instructions.
❑
Flush water system with 3 gallons of water, as specified
in the instructions.
❑
Check for water leaks at all connections.
❑
Turn on ice maker if refrigerator is connected to water
supply. (If not connected to water supply, turn off ice maker.)
✔
Final Checks
❑
Install air filter according to instructions in corresponding
packaging.
❑
Remove all shipping material.
❑
Set temperature controls to the recommended settings.
❑
Save instructions and other literature.
❑
Send in Registration Card or register your product online.
TOOLS REQUIRED
Depending on the width of the door opening, the following
tools may be required to remove, replace, and align the
refrigerator doors.
Tools Needed:
❑
#2 Phillips screwdriver – top hinge cover screws
❑
TORX
®
T25
®†
bit – top hinge screws, center hinge screws,
lower foot brackets
❑
1/4" hex nut driver – base grille, freezer drawer screws,
and brake/leveling feet
Tools Provided:
❑
1/8" and 3/32" hex keys – handle set screws and door
alignment
LEVELING
(AFTER MOVING TO FINAL LOCATION)
DOOR ALIGNMENT
Align Refrigerator Doors
✔
If doors are uneven:
❑
Ensure the refrigerator is level.
❑
Keeping both refrigerator doors closed, pull out the
freezer drawer. Locate the bottom hinge pin of the
right-hand refrigerator door. The alignment screw is
inside the bottom hinge pin.
❑
Insert the short end of the 1/8" hex key wrench (packed
with the Door Handle Installation Instructions) into
the bottom hinge pin until it is fully engaged in the
alignment screw.
To raise the refrigerator door, turn the hex key to the right.
To lower the door, turn the hex key to the left.
❑
Continue to turn the alignment screw until the tops of the
door are aligned.
✔
To steady or adjust the tilt of the refrigerator,
you must first remove the base grille:
❑
Use a 1/4" hex driver to remove both screws in base
grille.
❑
Grasp the grille firmly and pull it toward you. Open the
freezer drawer to access the brake feet.
Steady the Refrigerator
✔
If the refrigerator seems unsteady or rolls when the
door(s) or drawer(s) are pulled open:
❑
Using a 1/4" hex driver, turn both brake feet clockwise the
same amount until the brake feet are snug against the floor.
❑
Use a level to make sure the refrigerator is level from side
to side and front to back.
NOTE:
Having someone push against the top of
the refrigerator takes some weight off the brake feet,
making it easier to turn the feet.
❑
Replace base grille.
WATER FILTER INSTALLATION
❑
Locate the water filter compartment in the lower left-hand
side of the refrigerator compartment. Push on the right
side of the filter door to open.
❑
Align the arrow on the water filter cap with the cutout
notch in the filter housing and insert filter.
❑
Once the filter is inserted, turn the filter clockwise
90° (1/4 turn) until it locks into the housing.
❑
Push water filter door closed to latch.
❑
Flush 3 gallons of water through the water system to clear
air from the water line and to keep the dispenser from
dripping and/or avoiding decreased dispenser flow.
NOTE:
If the filter is not installed correctly, water may
dispense at a lower flow rate and there will be slower ice
production. Improper filter installation may also cause the
water filter housing to leak.
ICE MAKER ON/OFF SWITCH
Models with Ice Storage Bin on Door
❑
Open the left-hand refrigerator door.
❑
Open the ice storage bin door.
❑
Locate the ice maker switch on left wall of bin area.
Models with Ice Storage Bin in Freezer
❑
To turn the ice maker on, touch the Icemaker2 button
on display across the inside top of the refrigerator.
Ice storage bin release latch
If doors need to be removed during installation, remove/
replace doors at 90º to the unit. See the “Remove and Replace
Refrigerator Doors” section in the Use and Care Guide for
further instructions and for troubleshooting.
NOTE:
Remove outer and inner door together.
Shelf Height Adjustment
Shelf height can be adjusted by changing the adjustable
shelf mounts between their vertical and horizontal positions.
❑
Carefully lift the shelf off the shelf mounts and turn the
flipper to the desired orientation.
❑
Repeat for remaining shelf mounts.
❑
Ensure the shelf is properly seated on the shelf mounts.
INSTALLING AIR FILTER
Install the air filter behind the blue LED-lighted vent cover,
located on the rear wall near the middle of the refrigerator.
❑
Remove the air filter from its packaging.
❑
Pull out plastic cover to open the vented cover.
❑
Snap the filter into place.
A. Air filter
A
WARNING
Excessive Weight Hazard
Use two or more people to lift the refrigerator door.
Failure to do so can result in back or other injury.
†®TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.
IMPORTANT:
Please measure doorways and other obstructions in the installation path prior to conducting the installation.
❑
Minimum opening required is 33" (838 mm). If the opening is less than 36" (914 mm), removal of doors, drawer, and hinges is required.
IMPORTANT:
Connect to potable water supply only.
To view videos on door removal/
replacement, door adjustment,
water filter installation, air filter
installation, shelf adjustment or
removal, scan the code to the left
with your mobile device.
Installing Door-within-Door Knob
NOTE:
Knob-mounting setscrew is preinstalled on the knob.
Align the knob assembly with the lever at the middle of the
door. Using a clockwise motion, tighten the setscrew just until
the setscrew begins to contact the lever. Fully tighten.
IMPORTANT: Make sure to put together the knob assembly
prior to assembling the handle.
Do not open inner door when outer door is open. Close outer
door before opening inner door.
