3P05-PCR-LE 1
Setup Guide
PCR-LE Series
Three-phase Output Driver
Thank you for purchasing the PCR-LE Series Three-phase out-
put driver.
Connecting the outputs of PCR-LE Series in star connection
and installing the Three-phase Output Driver in these power
supplies allows them to be used as three-phase system power
supplies.
Features
Use of this device allows the PCR-LE series to provide the fol-
lowing enhanced functions, in addition to the PCR-LE’s stan-
dard functions.
• Three-phase Output
Use of the device allows the three PCR-LE to generate three-
phase output, in which the U-phase unit of the three power
supplies acts as a master and their V and W phase units acts
as slaves.
• Setting of Either the Line Voltage or Phase Voltage
• Independent Phase Voltage Setting
The individual phase voltage setting is possible on a phase
basis.
• Line Voltage Measurement
• Measurements of the Total Power, Total Apparent Power, and
Total Power Factor of Three Phases
Use of the device allows the totals of power and apparent
power obtained through measurement using the three PCR-
LE to be displayed. The total power factor of the three phas-
es can also be calculated from these total values.
• Variable Phase Difference
Check at Unpacking
Upon reception of the product, confirm that the package con-
tains the necessary accessories and that the device and ac-
cessories have not been damaged during transportation. If the
device is damaged or any accessory is missing, notify Kikusui
distributor/agent.
U phase boards
(1 pc.)
Power-sync cable
(1 m; 2 pcs.)
［
91-80-5099
］
Connecting cable (75 cm; 2 pcs.)
Cable: [91-80-9919]
Core: [96-00-0530]
Setup Guide
(This guide)(1 pc.)
V and W phase boards
(one each)
The indications
“
V
”
and
“
W
”
on the
panel part of each board.
Firmware version of PCR-LE
When using the 3P05-PCR-LE, the PCR-LE must be required
with the firmware version of 2.00 or later. If the firmware ver-
sion of the PCR-LE is 1.99 or previous version, the PCR-LE is
required for the firmware update.
When using the 3P05-PCR-LE, the firmware of all the PCR-LE
series that make up the system must be the same.
To check the firmware version of the PCR-LE, refer to the opera-
tion manual of the PCR-LE series. In case, the PCR-LE needs
update, contact your Kikusui agent or distributor.
Functional Restrictions during
Three-phase Operation
Use of the 3P05-PCR-LE allows the PCR-LE series to generate
three-phase outputs. The following functions are not available
when the device is installed in the power supplies.
DC mode
Regulation adjustment
High-speed response
You cannot use the 3P05-PCR-LE with the 2P05-PCR-LE Single-
Phase Three-Wire Output Driver Option.
KIKUSUI ELECTRONICS CORP.
1-1-3, Higashiyamata, Tsuzuki-ku, Yokohama, 224-0023, Japan
TEL: +81-45-593-7570 Fax: +81-45-593-7571
WEBSITE
http://www.kikusui.co.jp/en
The 3P05-PCR-LE is subject to export control laws.
The newest version of the operation manual can be downloaded from
Download service of Kikusui website.
The contents of this manual may not be reproduced, in whole or in part,
without the prior consent of the copyright holder.
The specifications of this product and the contents of this manual are
subject to change without prior notice.
© 2012
3P05-PCR-LE
PART NO. Z1-006-0
6
0, IA005173
Oct. 2016
PCR-LE Manual
