background image

(01/02)

KM816010

MAINTENANCE MANUAL

Kenworth SmartWheel Troubleshooting Guide

16

0Kenworth  SmartWheel  Troubleshoot-
ing Guide KM816010 01/02

16

CONTENTS

TITLE

PAGE

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Service Manuals  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
TIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Wiring Diagrams  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
How to use this Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Tools for Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Troubleshooting Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
A. Start - No Functions Work or Operation is Intermittent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

A1. Possible cause: Open circuit in BA11 or Gnd circuit to elect. module (circuits PCB 1, 2, 3, or 4 and G N D). . .5
A2. Possible cause: Bad electrical connection to hub or slip rings.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
A2. Possible cause: Bad electrical connection to hub or slip rings.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
A3. Possible cause: Bad electronics module or steering wheel hub.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

B. Horn Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

B1. Possible cause: No power or ground in horn circuit.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
B2. Possible cause: Bad horn relay in power distribution box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
B3. Possible cause: Problem in circuit R11HN.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
B4. Possible cause: Bad electronics module or steering wheel hub.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

C. Engine Retarder Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

C1. Symptom: Engine retarder will not turn on (1994 Cummins only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
C2. Symptom: Engine retarder will not turn on (all engines).  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
C3. Symptom: Retarder works only when button held down or does not turn on.. . . . . . . . . . . . . . . . . . . . . . . . . .21

D. Cruise Control Does Not Work  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

D1. Symptom: Cruise Control will not turn on.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
D2. Symptom: Cruise SET will not work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
D3. Symptom: Cruise RESUME will not work.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

E. Headlight Flash Does Not Work  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

E1. Symptom: Headlights do not turn on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
E1. Symptom: Headlights do not turn on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
E2. Symptom: Headlights do not flash on with SmartWheel switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
E3. Symptom: Headlights do not blink off with SmartWheel switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

F. Marker Lamp Flash Does Not Work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

F1. Symptom: Marker lights do not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
F1. Symptom: Marker lights will not turn on  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
F2. Symptom: Marker lights do not flash on with SmartWheel switch.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
F3. Symptom: Marker lights do not blink off with Smart  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Summary of Contents for SmartWheel KM816010














































Reviews: