background image

3 Plug in and switch on. The neon

light will come on. 

4 Your kettle will boil and switch off

automatically. To re-boil, wait a
few seconds - the on/off switch
needs time to reset.

If you experience problems

with your kettle switching

on and off during use or

switching off before boiling,

check that the flat element

is free from scale - see

“descaling”. If descaling

does not solve the problem

contact Kenwood customer

care.

Your kettle is fitted with a scale
filter to hold back limescale
particles.

If you find drops of water under
your kettle, don’t worry - it is just
condensation.

boil-dry protection

If you switch on with too little
water, your kettle will cut out
automatically. Switch off and let it
cool down before re-filling.
When it has cooled down, the
switch will reset itself.

care and cleaning

Before cleaning, unplug your kettle
and let it cool down.

the outside and powerbase

Wipe with a damp cloth, then dry.
Do not use abrasives - they will
scratch the metal and plastic
surfaces.

the inside

Wipe with bicarbonate of soda on
a damp cloth. Rinse thoroughly.

Even though your kettle comes
with a scale filter, you still need to
clean the inside (and the filter)
regularly.

the scale filter

1 Open the lid.
2 Slide the scale filter out 

.

3

either

rinse under the tap or use

a soft brush.

or

when descaling your kettle,

drop the filter in too. Rinse
thoroughly.

4 Slide the filter back in to refit.

descaling

Regular descaling of the flat
element will improve the
performance of your kettle. If the
kettle is not descaled regularly the
build up of limescale may result in
the following:

problems may be experienced
with the kettle switching on and
off during use or switching off
before boiling.

the kettle may take longer to
boil.

the flat element may be
damaged.

Please note not descaling your kettle
may invalidate your guarantee.

When limescale starts to build up
on the heating element, buy a
suitable descaler and descale your
kettle. After descaling, boil with
fresh water several times and
discard. Clean any descaler off the
kettle - it can damage the parts.

Some regions of the country have
chalky water. This makes boiled
water look cloudy and leaves a
deposit on the side of the kettle.
This is normal but can be removed
with regular cleaning.

Alternatively, to reduce limescale
build up, use filtered water to fill
your kettle. 

A range of Kenwood jug water
filters are available.

Call Kenwood on

023 92392333

and ask for customer care.

safety

Always use the filter and never
overfill – boiling water may splash
out.

Avoid contact with steam coming
out of the spout area when
pouring and out of the lid when
refilling.

Beware: the metal body of the
kettle will get hot during operation.

Keep small children away from the
kettle and never let the cord hang
down over the worktop edge - a
child could grab it and pull the
kettle down.

If you do not need so much cord,
shorten it by wrapping any excess
cord around the bracket on the
underside of the powerbase. 

.

Always unplug your kettle

when not in use.

Never put the kettle, powerbase,
cord or plug in liquid.

Do not use if there is 

any

damage

to the kettle, powerbase, cord or
plug. Get it checked or repaired:
see ‘service’.

This kettle is not intended for use
by young children or infirm persons
without supervision.

Young children should be
supervised to ensure they do not
play with the appliance.

Caution:

Do not operate the

kettle on an inclined surface.

Only use the powerbase supplied
and keep it clean and dry.

Make sure the lid is secure before
switching the kettle on.

Warning:

Do not open the lid

while the water is boiling.

Make sure the kettle is switched
off before lifting or pouring.

Remove the kettle from the base
before filling or pouring.

Never put the kettle near or on
cooker hot plates or gas burners.

This kettle is for boiling water only.

This kettle is for domestic use only.

Failure to observe these cautions
may result in damage to the kettle.

before plugging in

Make sure your electricity supply is
the same as the one shown on the
underside of your kettle.

important - UK only

The wires in the cord are coloured
as follows:
Green and Yellow = Earth, Blue =
Neutral, Brown = Live.

This kettle complies with European
Economic Community Directive
89/336/EEC.

before using for the first

time

Remove all packaging and any
labels.

Fill to ‘MAX’, boil, then discard the
water. Repeat 2 to 3 times.

know your Kenwood
stainless steel kettle

finger pad

flip top lid

lid catch release

water level windows

 

on/off switch with neon

360° powerbase

scale filter

cord wrap

to use your stainless
steel kettle

1 Fill the kettle through either the

spout or lid. To open the lid press
and hold down the lid release 

.

The water level must be between
‘Max’ and 200 mls (1 cup)

Be economical: do not boil more
water than you need.

To improve the quality of your
drinks always use fresh water.

Empty the kettle after each use.

2 Close the lid by pushing down on

the black finger pad area 

.

 

Reviews: