![background image](http://html1.mh-extra.com/html/kentek/ksgg-5408g/ksgg-5408g_instructions_1955372001.webp)
INSTRUCTIONS
LASER SHIELDS Laser Safety Eyewear
KSGG-5408G
PAGE 1 of 2
CE EN 207:2017, CE EN 208:2010, ANSI Z136, CE EN 166:2001 User Instructions for Laser Protective Eyewear
WARNINGS
USE THIS GOGGLE/SPECTACLE FOR DIFFUSE REFLECTION VIEWING ONLY
Failure to follow these safety precautions may result in serious eye injury, blindness or even death.
This laser protective eyewear is intended to offer protection against accidental exposure to certain lasers and must be marked with the requirements outlined in ANSI Z136
and/or CE EN 207 and/or CE EN 208 for the laser in use. Do not use this eyewear for any application other than stated. Do not make alterations to this eyewear. Do not operate
laser unless all users are wearing appropriate eye protection. Consult your Laser Safety Officer or Kentek's Laser Safety Officer if you have any concerns prior to use. This
product allows compliance with ANSI Z136. Familiarity with ANSI Z136 is necessary to ascertain compliance.
If the eyewear has a luminous transmittance of less than 20%, it is recommended to increase the intensity of illumination in the workplace; colored filters may reduce user
recognition of warning lights or warning signs. This eyewear may affect color recognition. Laser protective eyewear is only intended to give protection against accidental
radiation; both the limit values and the resistance tests are based on ANSI Z136 requirements and CE EN 207:2017 which requires a maximum period of 5 seconds. Avoid risk
of exposure to laser radiation due to reflection from reflective parts (including eyewear), tilting or misalignment of optical components. Inspect eyewear for discoloring, fading,
scratches or other damage. If laser protective eyewear is determined to be damaged replace prior to use. Reminder, eyewear that is optical class 3 is not intended for long term
use. The material which may come in contact with the wearer’s skin could cause allergic reactions to susceptible individuals. Laser protective eyewear against high speed
particles worn over standard ophthalmic spectacle may transmit impact, thus creating a hazard to the wearer. Laser protective eyewear which is damaged, has scratched
oculars or has undergone a color change shall not be used anymore. In case of filters with angle dependent transmittance any information shall be given that the protection is
only provided for angles of incidence up to 30°. When protection against high-speed particles at extremes of temperature is required the selected eye-protector should be
marked with the letter T immediately after the impact letter, i.e. FT, BT or AT, where impact letters are F for Low energy impact, B for Medium energy impact and A for High
energy impact. If the impact letter is not followed by the letter T then the eye protector shall only be used against high speed particles at room temperature. Regarding
compatibility of markings, if the impact symbols F, B or A on the ocular and the frame are not common to both, the lower level will be assigned to complete the eye protector.
EXPLANATION OF CE EN 207:2017 MARKINGS
A
B
C
D
E
F
520-532
D
LB5
KTK
S
A. Wavelength (nm) for which the eyewear protection is afforded
B. Test condition for laser type in accordance with Table 4 CE EN 207:2017:
D - Continuous Wave (CW) laser (minimum exposure duration 5 seconds)
I - Pulsed laser (>10
-6
s to 0.25 s, 50 pulses minimum)
R - Q-switched pulsed laser (≥10
-9
s to 10
-6
s pulsed length, 50 pulses minimum)
M - Mode-coupled laser (Pulse length <10
-9
, 50 pulses minimum)
C. Scale number - equates to the protection level afforded by the filter and frame when exposed to laser radiation as specified in Table 1 CE EN
207:2017
D. Manufacturer's identification mark - KTK
E. S - increased robustness of mechanical strength (CE EN 168:2001 clauses 3.1, 3.2; 22mm ball at 5.1 m/s). If no symbol is given, mechanical
strength is minimum robustness.
F. CE certification mark
EXPLANATION OF CE EN 208:2010 MARKINGS
A
B
C
D
E
F
G
1W
2x10
-4
J
532
RB3
KTK
S
A. Maximum laser power
B. Maximum pulse energy
C. Wavelength (nm) for which the eyewear protection is afforded
D. Scale number - protection level afforded by the filter and frame when exposed to laser radiation as specified in Table 1 CE EN 207:2017
E. Manufacturer's identification mark - KTK
F. CE certification mark
G. Mechanical strength symbol
Printed January 7, 2023
Copyright 2023 by Kentek Corporation. All rights reserved.
5 Jarado Way
.
Boscawen, NH 03303 USA
.
800-432-2323
.
+1-603-223-4900
www.kenteklaserstore.com
.