background image

BLUETOOTH STEREO HEADSET

CASQUE STÉRÉO BLUETOOTH

CASCO CON AURICULARES ESTÉREO BLUETOOTH

HA-W700BT -J/C

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

MANUAL DE INSTRUCCIONES

1.  To reduce the risk of electrical shocks, fire, etc.:

 Do not remove screws, cover or cabinet.

 Do not expose this appliance to rain or moisture.

2. For your safety…

 Never use the unit when driving a car, motorcycle, or bicycle. This 

could result in an accident. 

 Pay special attention to traffic around you when using the 

headphones outside. Failure to do so could result in an accident.

 Be careful not to turn up the sound volume too high. Your hearing 

can be damaged from listening to sounds at excessive volume for 
long periods.

 Do not disassemble or modify the unit.

 Do not allow flammable, water or metallic objects to enter the unit.

 If you find skin problems where the headphones are in contact 

with the skin, stop using the headphones; otherwise, it may cause 
inflammation or irritation to the skin.

 In dry air such as in winter, you may feel a static shock when using 

the headphones.

3.  Avoid using the headphones…

 in places subject to excessive humidity or dust

 in places subject to extremely high (over 40°C or 104°F) or low 

 (under 0°C or 32°F) temperatures

4.  DO NOT leave the unit…

 exposed to direct sunlight

 near a heater

5.  To protect the unit, DO NOT…

 allow them to get wet

 shake them or drop them against hard objects

Thank you for purchasing this JVC product. Before you begin operating this unit, please read the operating instructions carefully to be sure you get 
the best possible performance. If you have any questions, consult your JVC dealer.

6.  For using the headphones…

 Attach the ear pieces firmly when replacing them; otherwise, the ear 

pieces may be left in your ears when taking the headphones off. If the 
ear piece is left in your ear, be careful not to push it deep into the ear 
canal.

 Be careful not to apply the power that exceeds the headphones’ input 

capacity. This may result in sound distortion and could damage the 
oscillation board.

 Grasp and pull the plug itself to disconnect the headphones. Do not pull 

on the cord.

 When the ear pieces get dirty, detach the ear pieces and wash them in 

water-diluted detergent. After washing, dry the ear pieces and attach to 
the headphones.

 Replace the ear pieces when: they lose its elasticity; they are stained 

badly; they are broken or deformed.

 The ear pieces will deteriorate with age even in normal use and 

maintenance.

 Store the ear pieces in a place where children cannot reach to avoid the 

risk of the accident such as swallowing them.

 

When using canal type headphones, you may hear the sound of cord 
rubbing together or the sound of vibrations which travels through your 
body when walking.

7. For safe use of battery…

 Use only the supplied charging unit to charge the battery.

 Be sure to use the supplied AC adaptor.

 There are no serviceable parts inside. Consult your dealer to replace 

the built-in battery.

 When discarding batteries, environmental problems must be 

considered and the local rules or laws governing the disposal of these 
batteries must be followed strictly.

English

Listening to Music

Preparation: 

•  Make sure that the 

Bluetooth

 device can transmit music through the 

Bluetooth

 connection (compatible with the A2DP profile of 

Bluetooth

)

•  Finish pairing between the unit and the 

Bluetooth

 device.

•  Turn on the 

Bluetooth

 device.

1  Turn on the unit.

2 Execute the 

Bluetooth

 (A2DP) connection on the 

Bluetooth

 device.

•  When the connection is completed, the blue lamp flashes repeatedly.
•  Refer also to the instruction manual supplied for the target device.
•  If the connection is not completed within five minutes, the unit 

automatically turns off. In this case, turn the POWER switch to OFF 
and turn it back to ON, and then repeat the procedure from step 1.

3  Start playback on the 

Bluetooth

 device.

•  Refer also to the instruction manual supplied for the target device.
•  Set the connected 

Bluetooth

 device so that the device emits the sound 

through the 

Bluetooth

 stereo headphones.

4  Adjust the volume by tilting the control switch up or 

down.

Basic controls available for the device:

Button

Press

Press and hold

6

Play/pause

Stop

*

¢

Skip (to the next)

*

Search (to forward)

*

4

Skip (to the previous)

*

Search (to backward)

*

*  Not available for some devices.

•  You can perform some of the 

Bluetooth

 device operations with 

the control switch of the unit if the device is compatible with the 
AVRCP profile. The operations you can do may vary depending on 
the device you use.

 

Refer also to the instruction manual supplied for 

the target device to see the available operations.

When using the unit as a Bluetooth receiver

The unit can be used as a 

Bluetooth

 receiver. Connect the PHONES 

terminal on the unit to the external input terminal (

ϕ

3.5 mm stereo mini 

jack) on the audio equipment using the supplied connection cord.
•  When connecting to an RCA pin plug, use a cord separately purchased.
•  Before connection, turn off the unit and the audio equipment.
•  Set the volume of the audio equipment to minimum before executing 

pairing or making  connection between the unit and the audio 
equipment.

To stop using the unit 

Disconnect the 

Bluetooth

 connection on the 

Bluetooth

 device and turn off 

the unit.

For the better sound and comfort fit of the headphones

The medium-size ear pieces are attached to the supplied headphones 
when purchased.
You may not enjoy the bass sound fully if the ear pieces are not fit 
to your ears. To enjoy better sound while reducing sound leakage 
and getting full noise canceling effect, choose the ear pieces from 
the supplied three sizes (Small, Medium, or Large) and adjust their 
positions to fit them to your ears.

Troubleshooting

What appears to be trouble is not always serious. Check the following 
points before consult your JVC dealer.

Cannot pair the devices.

 You cannot pair the 

Bluetooth

 device having receiving function only.

 

Bring the devices as closer as possible.

Cannot connect the devices.

 Pairing is incomplete. Perform the pairing again.

 Check that the 

Bluetooth

 communication function is activated in the 

Bluetooth

 device.

  When you press the CALL button, the unit will search for the last 

connected 

Bluetooth

 device.

The sound is intermittent/The communication range is small.

 Although 

Bluetooth

®

 wireless technology can transmit the contents 

within the range of approx. 10 m, obstacles (human bodies, metallic 
objects, wall, etc.) or radiowave condition may affect the sound and 
decrease its range.

 The sound may be intermittent in the following cases. Avoid the 

following conditions when you use this unit.

–  Places where the wireless local area network is applied.
–  Near the microwave oven.
–  Near the other 

Bluetooth

 devices.

–  Places where the radiowave is used.

No sound.

 The connection between the 

Bluetooth

 device and this unit is 

incomplete. Connect the devices again.

 The setting of the 

Bluetooth

 device is incorrect. Set the connected 

Bluetooth

 device so that the device emits the sound through the 

Bluetooth

 stereo headphones.

Printed in China

LNT0091-001A

© 2007 Victor Company of Japan, Limited

Battery disposal

When disposing the unit, take off the built-in lithium-ion rechargeable 
battery and dispose appropriately for environmental protection.

1. Take off the screws with the Phillips-

head screwdriver.

2. Open the case and use 

scissors to cut the cords one 
by one to take off the battery.

•  Do not take off the battery from 

its case when you dispose of the 
battery.

•  Do not cut two cords at the same 

time since it may cause a short-
circuit.

Calling through the unit

Preparation: 

• Activate the 

Bluetooth

 communication function on your cellular phone.

•  Finish pairing between the unit and your cellular phone.

1  Turn on the unit.

2 Execute the 

Bluetooth

 connection on the cellular phone.

•  Refer also to the instruction manual supplied for the cellular phone.
•  If the connection is not completed within five minutes, the unit 

automatically turns off. In this case, turn the POWER switch to OFF 
and turn it back to ON, and then repeat the procedure from step 1.

•  When using a cellular phone supports both HFP and HSP 

Bluetooth

 

Profile, use HFP for this unit.

•  When the connection is completed, the blue lamp flashes repeatedly.

Basic controls available for the cellular phone connected with HFP:

Status

CALL button

Press

Press and hold

Waiting

Start voice dialing

Redial

Dialing by 
voice dialing

Cancel voice dialing

Calling

Cancel calling

Incoming

Answer the call

Reject the call

Answering

Finish the call

Switch the device 
(between cellular phone 
and the unit)

Basic controls available for the cellular phone connected with HSP:

Status

CALL button

Press

Press and hold

Waiting

Redial

Calling

Cancel calling

Cancel calling or switch 
to the unit

Incoming

Answer the call

Reject the call

Answering

Finish the call

Switch the device 
(between cellular phone 
and the unit)

•  These functions may not available for some cellular phones.
•  When answering a call on cellular phone, these functions may not 

work.

To make a call while playing back music

When connecting the cellular phone by using HFP or HSP 

Bluetooth

 

Profile, you can make a call by using the cellular phone.

To answer a call while playing back music

When a call comes in, the playback sound turns to ring tone. Press the 
CALL button to answer the call.

To finish the call

Press the CALL button. The playback sound comes back. (The playback 
sound may not come back in some cellular phone.)

You can register up to 8 

Bluetooth

 devices to the unit.

•  The device that has the oldest connection date will be overwritten when 

you register a 9th 

Bluetooth

 device.

Before pairing...

•  Make sure that the unit is turned off.
•  Turn on the target 

Bluetooth

 device and place it within 1 m from the 

unit.

1  Turn on the unit with pressing and holding the CALL 

button to make it in the pairing mode.

The blue lamp and the red lamp will start flashing continuously as the 
unit finds the target 

Bluetooth

 device (pairing mode). Release the CALL 

button after the flashing starts.
•  Finish the steps below within about 3 minutes after the flashing 

starts (the pairing mode is automatically cancelled after the period). 
Turn off the unit and start from step 1 again when you cannot finish 
the operation.

2  Execute pairing operation on the target 

Bluetooth

 device 

to find the unit.

The device shows the list of 

Bluetooth

 devices found. The unit is 

recognized as “JVC HA-W700BT”. Repeat from Step 1 again when 
“JVC HA-W700BT” is not found.
•  Refer also to the instruction manual supplied for the target device.

Registering a Bluetooth device – Pairing

3  Select “JVC HA-W700BT” on the target 

Bluetooth

 

device.

4  Enter “0000” when the Pass code* is requested on the 

target 

Bluetooth

 device.

Pairing is finished when the red lamp goes out and the blue lamp 
flashes three times repeatedly.
*  also called as “pass key”, “PIN code”, “PIN number”, etc.

5 Execute 

Bluetooth

 connection to the unit on the target 

Bluetooth

 device.

The unit saves the target as the last connected 

Bluetooth

 device.

•  Refer also to the instruction manual supplied for the target device.
• Some 

Bluetooth

 device will automatically connect with the unit after 

pairing is finished.

•  When the connection is completed, the blue lamp flashes repeatedly.

To pair with devices which cannot show the 

Bluetooth

 device list...

On some 

Bluetooth

 devices, pairing may automatically be established by 

making both the unit and the target device in the pairing mode. Refer also 
to the instruction manual supplied for the target device to make it in the 
pairing mode.

CAUTION

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is 

subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including 

interference that may cause undesired operation.

CAUTION:

 Changes or modifications not approved by JVC 

could void user’s authority to operate the equipment.

Contact

Address:  JVC AMERICAS CORP.

 

JVC COMPANY OF AMERICA

 

1700 Valley Road, Wayne, N.J. 07470

Telephone: 1 (800) 252-5722

Note:

 This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to Part 

15 of the FCC rules. These limits are designed to provide 

reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and 

can radiate radio frequency energy and, if not installed and 

used in accordance with the instructions, it may cause harmful 

interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for 

help.

IC INFORMATION

This device complies with RSS-210 of the IC Rules. Operation is 

subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including 

interference that may cause undesired operation of the 

device.

CAUTION:

 Changes or modifications not approved by JVC 

could void user’s authority to operate the equipment.

Contact

Address:  JVC CANADA INC.

 

21 Finchdene Square, Toronto, ON  M1X 1A7

Telephone: (416) 293-1311

e-mail: [email protected]

Note:

 This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to 

Industry Canada’s RSS-210. These limits are designed to 

provide reasonable protection against harmful interference 

in a residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, it may cause 

harmful interference to radio communications. However, there 

is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for 

help.

INFORMATION SUR IC

Cet appareil est conforme à la RSS-210 du réglement de la IC. 

Le fonctionnement est sujet aux deux conditions suivantes:

(1) Cet appareil ne peut causer d’interférences nuisi-bles

(2) Cet appareil reçoit toute interférence même les interférences 

qui peuvent occasioner un mauvais fonctionnement.

ATTENTION:

 Les changements ou les modifications non 

approuvés par JVC risquent de retirer à l’utilisateur le droit 

d’utiliser l’appareil.

Contact

Adresse:  JVC CANADA INC.

 

21 Finchdene Square, Toronto, ON M1X 1A7

Téléphone: (416) 293-1311

e-mail: [email protected]

Remarque:

 L’appareil a été testé et jugé conforme aux limites 

des appareils numériques de classe B, aux termes de la 

réglementation RSS-210 de l’industrie du Canada. Ces limites 

ont pour but d’assurer une protection raisonnable contre les 

interférences parasites lorsque l’appareil est utilisé dans 

une installation résidentielle. Cet appareil engendre, utilise 

et peut émettre une énergie radioélectrique et, s’il n’est pas 

installé et utilisé en stricte conformité avec ces instructions, il 

peut provoquer des interférences parasites dans les liaisons 

radiophoniques. Ceci ne garantit pas pour autant qu’une 

installation particulière n’émettra aucune interférence. Si 

l’appareil engendre des interférences parasites avec la réception 

radio ou télévision, ce qui pourra être déterminé en éteignant 

puis en rallumant l’appareil, il est conseillé à l’utilisateur 

d’essayer de corriger les interférences en prenant l’une des 

mesures ci-dessous:

•  Modifier l’orientation ou changer l’emplacement de l’antenne 

de réception.

•  Eloigner davantage l’appareil du récepteur.

•  Brancher l’appareil dans une prise d’un circuit différent de 

celui auquel le récepteur est raccordé.

•  Demander l’aide de son agent ou d’un technicien radio/

télévision qualifié.

IMPORTANT

CAUTION:

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG 

WITH AN EXTENSION CORD, RECEPTACLE OR OTHER 

OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO 

PREVENT BLADE EXPOSURE.

ATTENTION:

POUR PREVENIR LES CHOCS ELECTRIQES NE PAS 

UTILISER CETTER FICHE AVEC UN PROLONGATEUR, UNE 

PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, 

SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND 

SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

(1) This device may not cause interference.

(2) This device must accept any interference, including 

interference that may cause undesired operation of the device.

(1) Ce produit ne cause pas d’interférence.

(2) Ce produit doit accepte toute interférence, incluant 

interférence qui peut causé opération non désiré.

ENGLISH

This product’s performance would be degraded under a strong 

electro-static environment. And the function would be self-

recoverable after the above case.

This product’s performance would be degraded since the 

disturbance from the mains cord. And the function would be self-

recoverable after the above case.

FRANÇAIS

Les performances de ce produit se détérioreront dans un 

environnement fortement électro-statique. Par ailleurs, le 

fonctionnement se restaurera de lui-même dans le cas ci-dessus.

Les performances de ce produit se détérioreront en cas 

de perturbations du cordon d’alimentation. Par ailleurs, le 

fonctionnement se restaurera de lui-même dans le cas ci-dessus.

ESPAÑOL

El rendimiento de este producto puede deteriorarse en un entorno 

con campos electrostáticos fuertes. El funcionamiento se repondrá 

a la normalidad después del caso arriba mencionado.

El rendimiento de este producto puede deteriorarse debido a las 

perturbaciones del cable de la red eléctrica. El funcionamiento se 

repondrá a la normalidad después del caso arriba mencionado.

Hearing Comfort and Well-Being

•  Do not play your personal audio at a high volume. Hearing 

experts advice against continuous extended play.

•  If you experience a ringing in your ears, reduce volume or 

discontinue use.

Traffic safety

•  Do not use while operating a motorized vehicle. It may create a 

traffic hazard and is illegal in many area.

•  You should use extreme caution or temporarily discontinue use 

in potentially hazardous situations.

•  Even though your earphones are of the open-air type designed 

to let you hear outside sounds, don’t turn up the volume so 

high that you can’t hear what’s around you.

Specifications

General

Bluetooth

 version:

 

Bluetooth

 2.0 certified

Output power:

 

Bluetooth

 power class 2

Service area:

 max. 10 m (10.9 yd.)* 

*  Communication range may vary depending on the environmental 

conditions.

Frequency band:

 2.4 GHz (2.4000 GHz – 2.4835 GHz) 

Bluetooth

 profile:

A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/Video 
Remote Control Profile), HFP (Hands-free Profile), HSP (Headset 
Profile)

Supported Codec:

 SBC (Subband Codec)

Power supply: 

Built-in lithium-ion rechargeable battery (DC 3.7 V)

Battery life*: 

Music play time: up to 11 hours

 

Standby time: up to 100 hours

* Depends on use.

Mass:

 35 g (1.23 oz.) (including headphones)

Headphones (J48139-001)
Frequency response:

 10 Hz – 23,000 Hz

Sensitivity:

 103 dB/1 mW

Accessories

AC adaptor x 1 (S004CU0500050), Ear pieces 3 pairs (Small, Medium, 
Large), Charging unit (J48140-001) x 1, Connection cord (0.7 m (2.3 ft.) 
stereo mini plug - stereo mini plug)

Designs and specifications are subject to change without notice.

 

iPod is a trademark of Apple Inc., registered in the U.S. and other 
countries.

 

The 

Bluetooth®

 word mark and logos are registered trademarks owned 

by Bluetooth SIG, Inc. and any use of such marks by Victor Company 
of Japan, Limited (JVC) is under license. Other trademarks and trade 
names are those of their respective owners.

Parts name

1

8

2

345 6

7

9

p

q

1

 

 (CALL) button 

 

Controls the cellular phone calling through this unit.

2

  Strap hole

3

  Control switch (

6

 button, +/– buttons)

 

• 

6

 button: Controls the music player connected 

with this unit.

 

•  +/– buttons: Adjusts the volume level. When you 

press + or – button with the highest or lowest 

volume level, beep sound is heard.

4

  Red lamp 

 

Indicates the battery status of this unit.

5

  Blue lamp 

 

Indicates the communication status between this 

unit and 

Bluetooth

 device.

6

  Microphone 

 

Picks up your voice when calling through this unit.

7

  Stereo mini jack 

8

  Headphones 

9

  Battery charge terminal 

p

  Clip 

q

  POWER switch

 

Slides to turn on or off this unit.

Battery

Features

This unit is a wireless stereo headset using 

Bluetooth

® wireless technology.

Music

Call

Control

Control

iPod with 

Bluetooth

 

Transmitter (AA-T100BT)

Bluetooth

 cell 

phone

As 

Bluetooth

 Stereo Headset

As 

Bluetooth

 Receiver

Bluetooth

 audio source

Music

•  Checking the battery charge

Press the 

6

 button while holding the CALL button. (Press the 

6

 

button within two seconds after pressing CALL button.) The red lamp 
lights or flashes to show the battery remains.
•  The red lamp starts slow flashing automatically when the battery 

become nearly empty. 

Battery charging

Charge the built-in lithium-ion rechargeable battery first to use this unit.

1  Connect the AC adaptor to the charging unit.

•  Do not use any AC adaptor other than the supplied one.

2  Connect the AC adaptor to the AC outlet.

3  Put the unit on the charging stand.

The red lamp lights up when the charging starts.
The blue lamp will light up when the charging is finished (the red lamp will 
turn off).
•  When the unit is turned off, it takes five hours to charge the battery to full 

when it is empty.

•  Disconnect the AC adaptor from the AC outlet when you do not use the 

charging unit for a extended period of time.

•  Do not pull the cord when disconnecting the AC adaptor.
•  Do not handle the power cord with wet hands!
•  Do not bend the power cord sharply.

Battery charge 

terminal

Red lamp

Battery level

Full

-

-

-

-

-

-

Halfway

-

------------

-

Low

---------------

Need to charge

About Bluetooth

Bluetooth

 is a short-range wireless radio communication technology for 

the mobile device such as cellular phones, portable PCs, and other devices. 
The 

Bluetooth

 devices can be connected without cables and communicate 

each other.

About Bluetooth Profile

Bluetooth

 Profile designates the way of communication between 

Bluetooth

 

devices. The system supports the following 

Bluetooth

 Profiles.

A2DP:

 Advanced Audio Distribution Profile

The profile controls sending/receiving the high-quality audio contents.

AVRCP:

 Audio/Video Remote Control Profile

The profile controls the functions of audio/video devices such as playing, 
stopping, pausing and volume control.

HSP:

 Headset Profile

The profile controlling the cell phone, and controlling the connection 
between the devices.

HFP:

 Hands-Free Profile

The profile controls the hands-free call with cell phone.

About pairing

Pairing creates a unique and encrypted link between two 

Bluetooth

 devices 

and lets them communicate with each other. 

Bluetooth

 devices will not 

work if the devices have not been paired.

Cautions on Bluetooth communication

• Microwaves emitted from 

Bluetooth

 devices may affect the operation 

of electronic medical devices. Turn off this unit and other 

Bluetooth

 

devices in hospitals, airplanes, trains, or crowding places.

• 

Bluetooth

 devices use 2.4 GHz band, which is the same as that used by 

wireless LAN devices and microwave oven. Interference may occur 
near these devices and cause noise, disconnectivity, or a decrease of 
communication speed.

•  Connection with all 

Bluetooth

 devices cannot be guaranteed. 

Connectivity, operation, display indication or function may differ 
depending on the characteristics and specification of the devices.

• Some 

Bluetooth

 devices take more time to establish connection.

• To use the 

Bluetooth

 functions, the 

Bluetooth

 devices are required to be 

compatible with the same 

Bluetooth

 profiles as this unit is. However, the 

functions may not be available depending on the specifications of the 

Bluetooth

 device even when it is compatible with the same profiles.

LED flashing patterns

Status

LED

Flashing pattern

Pairing

Blue

-

-

-

-

-

-

-

-

-

-

-

-

-

Red

-

-

-

-

-

-

-

-

-

-

-

-

-

Waiting connection

Blue

-

-

--------------

-

-

----------

Red

------------------------------------------

Communicating

Blue

---------------------

-----------------

Red

------------------------------------------

Bluetooth

 cell phone 

with music player

Music & Call

Control

AC adaptor

Optional (not supplied) 

Bluetooth

 Transmitter 

(AA-T100BT)

Connection cord 

(supplied) 0.7 m (2.3 ft)

Audio in

HA-W700BT_JC4.indd   1

HA-W700BT_JC4.indd   1

2007.10.12   5:04:45 PM

2007.10.12   5:04:45 PM

Reviews: