EN
AU/NZ
CORRECT CARE AND USAGE INSTRUCTIONS
STORAGE:
When not in use or during transportation the faceshield/visor should be
stored in a container such that it is out of direct sunlight, not in contact with solvents
and can not be damaged by physical contact with hard surfaces/items. Do not store
outside the temperature range of –20°C or +50°C or with humidity above 90%RH.
UNPACKING INSTRUCTIONS:
Carefully remove the faceshield/visor from the
packaging, taking particular note of any instructions printed on or included with
the faceshield, and remove the protective film on the visor. Do not use if items
appear damaged or missing.
CLEANING / DISINFECTION:
To maintain the faceshield/visor in the best
possible condition do not use abrasive materials to clean them. Rinse in a 1%
solution of mild detergent in tap water and dry with a soft cloth.
USE:
No protection is given unless the visor is correctly fitted and in the lowered
position. The faceshield can be raised or lowered as required by loosening the
two side pivot nuts.
MAINTENANCE:
A range of replacement parts is available, including
welding filters and clear protective lenses. Instructions for fitting spare parts
will be supplied. It is likely that the faceshield will require a replacement of
component parts or the complete unit after a period of 2 to 3 years
POLYCARBONATE & ACETATE VISORS:
These visors are suitable for protection
against high speed particles, liquid splashes, molten metal, hot solids and electrical
hazrads as marked.
Warning:
They are not suitable for furnace or welding use.
WIRE GAUZE VISOR:
This visor is suitable for use for forestry work in
combination with JSP Invincible industrial Safety Helmets and Visor Carrier or
a JSP Invincible Browguard. The ‘’S’’ symbol on the visor indicates that it meets
the requirements of Increased Robustness as defined by EN1731.
Warning:
The mesh eye and face protector does not protect against liquid splash
(including molten metal), hot solids, electrical hazards, infrared and ultra violet
radiation. Mesh eye and face protectors marked with “S” should not be used
when there is a forseeable risk of any hard or sharp flying particles.
GREEN SHADED VISOR:
The green shaded visor should only be used for gas
welding, it is not suitable for use as a general eye protector.
WARNING:
Susceptible individuals may experience an allergic reaction to those
parts of the faceshield/visor that come into contact with the wearers’ skin. If
this is the case, leave the hazard area, remove the faceshield/visor and seek
doctor’s advice. None of the materials used in the manufacture of the faceshield
are known to adversely affect user hygiene or health. Eye-protectors against
high speed particles worn over standard ophthalmic spectacles may transmit
impacts, thus creating a hazard to the wearer. This eye protector is suitable for
use to the lowest marking on the browguard or visor. If protection against high
speed particles at extremes of temperature is required then the selected eye-
protector should be marked with the letter T immediately after the impact letter,
i.e. FT, BT or AT. If the impact letter is not followed by the letter T then the eye
protector shall only be used against high speed particles at room temperature.
Class 3 optical quality oculars are not designed for long term use. Filter
screens carry the appropriate grade marking, see table for suitabiliy of
screen filter for the task to be performed.
These eye protectors may transmit
impacts to eye-wear enclosed by the eye protector. Clear material faceshields
are not intended for furnace/welding use. Wire mesh faceshields are not suitable
for protection against high speed particles, liquid splash, molten metal splash,
hot solids, electrical hazards, furnace or welding use.
KEY TO FRAME & OCULAR MARKINGS:
EN166
European Standard Number for Eye Protection
EN169
European Standard Number for Welding filters
EN175
European Standard Number for Welding eye/face protection
EN1731
European Standard Number for Wire Gauze Visors
AS/NZS1337.1 Eye & face protectors for occupational applications
AS/NZS1337.2 Mesh eye & face protectors for occupational applications
Manufacturers Trademark
2-_._
Ultraviolet filter scale number
3 Liquid Droplets
5-_._
Sunglare filter performance
4 Large Dust Particles
1
Optical Quality
(1=high, 3=low)
5
Gas and fine
Particles
M or 9
Molten Metals & Hot Solids
8 Short circuit electric arc
H
High temperature
O Outdoor Untinted
V
High impact
C Splash proof
I
Medium Impact
K
Resistance to surface
damage by fine
particles
B
Medium energy high speed
particle impact
F
Low energy high speed
particle impact
N
Anti-Mist
S
Increased robustness
T
If protection at extremes of temperature is required
select eyewear including a T after the impact marking
A copy of this manual and the Declaration of Conformity for the product can be found on the product page: documents.jspsafety.com
FACESHIELDS & VISORS
EN166: 2001, EN1731: 2006, EN169: 2002, EN175: 1997, AS/NZS1337.1, AS/NZS1337.2
www.jspsafety.com
RFKZ
-
000
-
800
_20-07
+44 1993 826051
JSP Safety GmbH.
40549, DE
JSP Ltd.
OX29 0TA, UK
Certified by: BSI Group
The Netherlands B.V., (NB2797).
BSI Group The Netherlands B.V.,
John M. Keynesplein 9, 1066 EP,
Amsterdam, The Netherlands.
Certified by: BSI Group
7/15 Talavera Road,
Macquarie Park, NSW
2113, Australia
ASSEMBLY FOR CLEAR & WIRE GAUZE VISORS
ASSEMBLY & ADJUSTMENT OF FACESHIELDS:
In use ensure the faceshield/helmet combination fits comfortably,and securely to the head. If fitted to a helmet combination, follow the adjustment instructions
supplied with the helmet. If fitted to a browguard, adjusted as follows:
1.
Slide left half of crown strap through loops on the right half to obtain correct height, engage retaining pin in correct hole.
2.
Place faceshield on head and check height setting. Ensure headband is not too low on brow. If necessary repeat step 1 until correct height adjustment is achieved.
3.
With faceshield on head turn adjuster knob or adjust elastic to obtain a firm and comfortable fit.
Suitable accessories and spare parts are available from the retailer. Do not use accessories and spare parts not approved by the manufacturer.
