ASSEMBLY INSTRUCTIONS FOR THE
TIMBERLINE and TIMBERLINE OUTFITTER TENTS:
Component List:
1 Tent Body,
1 Tent Bag
4 Poles
1 Spanner
1 Tent Fly,
2 Fly Rods
1 Pole Bag
2 Junction Tubes
1 Stake Bag and Stakes
s 5NROLL AND UNFOLD THE TENT AND LAY IT ON THE GROUND 2EMOVE
THE mY AND OPEN THE TENT DOOR $O NOT STAKE DOWN THE TENT JUST YET
"UT IN WINDY CONDITIONS STAKE DOWN ONE FRONT CORNER INTO WIND
NOTE:
$O NOT DROP TENT BAG OR POLE BAG ON ITS END $O NOT BOUNCE TENT
BAG ON ITS END TO GET TENT OUT 4HESE ACTIONS MAY CUT THE SHOCK CORD ANDOR
DAMAGE THE POLE ENDS
s !SSEMBLE ALL THE SHOCKCORDED POLES -AKE SURE EACH POLE SECTION HAS lRMLY
SEATED INTO THE ADJACENT SECTION 4RY TO KEEP THE POLES FROM SNAPPING TOGETHER
AS THIS CAN DAMAGE THE ROD ENDS 4HROUGH USAGE THE ALUMINUM FRAME MAY
BEND SLIGHTLY AND TAKE A SET THIS NORMALLY DOES NOT AFFECT PERFORMANCE
s 0LACE THE TAPERED END OF A POLE ONTO THE DIAGONAL HOLE IN THE JUNCTION TUBE
4HE JUNCTION TUBE IS MARKED 50 24 ;4/0 2)'(4 ON 4,= SO THE POLE WILL
SEAT AT THE CORRECT ANGLE )NSERT A CORNER PIN INTO THE OTHER END OF THE POLE
3EE FIG
s 2EPEAT WITH THE SECOND POLE AND AT THE BACK OF THE TENT WITH THE LAST TWO
POLES AND THE REMAINING JUNCTION TUBE
s $ISCONNECT THE RODS IN THE MIDDLE OF THE SPANNER 0LACE ONE END OF
THE SPANNER THROUGH THE CENTER HOLE OF THE lRST JUNCTION TUBE 0LACE
THE OPPOSITE END OF THE SPANNER
THROUGH THE CENTER HOLE IN
SECOND TUBE
3EE FIG
s 0USH DOWN ON THE DISCONNECTED
RODS UNTIL THEY JOIN TOGETHER 4HIS FORMS
THE FREE STANDING FRAME 3EE FIG
s #ONNECT THE TENT TO FRAME BY PULLING THE SHOCKCORDED LOOPS AT THE
PEAKS OF THE TENT OVER THE JUNCTION TUBES 3NAP TENT CLIPS TO THE POLES
NOTE:
*UNCTION TUBES CAN BE TIED TO THE TENT WITH THE STRINGS PROVIDED
4IE ONE END TO THE SHOCKCORD LOOP 0ASS THE OTHER END THROUGH THE
HOLE IN THE JUNCTION TUBE AND TIE A KNOT
3EE FIG
s /RIENT THE TENT IN THE DESIRED LOCATION AND STAKE IT DOWN
s &IT EACH OF THE mY RODS OVER THE TIP OF THE SPANNER SECTION PROTRUDING
THROUGH EACH JUNCTION TUBE
s $RAPE THE mY OVER TENT SO THE CENTER 3HOOKS ; SEWN ON THE UNDERSIDE
OF THE FLY = LINE UP WITH THE RODS
s )NSERT THE CENTER 3HOOK INTO ONE END OF THE FLY ROD 0ULL THE OPPOSITE
3HOOK AND INSERT IT INTO THE END OF THE SECOND FLY ROD
TIMBERLINE SERIES TENTS ARE EQUIPPED WITH
HIGH / LOW VENTING DOORS:
s 4O ALLOW COOL AIR INTO THE TENT UNZIP THE LOW VENT ON THE DOOR
AND HOLD OPEN WITH THE HOOK AND LOOP TAB
s 4O VENT THE FLY UNZIP THE TWO ZIPPERS AT THE BASE OF THE VESTIBULE
s 4O ALLOW WARM MOIST AIR TO ESCAPE UNZIP THE PEAK OF THE DOOR
AND ROLL DOWN ANDOR THE PEAK OF THE BACK WINDOW
OPTIONAL EQUIPMENT:
Annex:
&RONT AWNING FOR STORING GEAR AND COOKING
Gear Loft:
-ESH HAMMOCK ATTACHES TO RINGS INSIDE THE TENT
FOR DRYING CLOTHES OR STORING ACCESSORIES
Floor Saver:
0LACE UNDER TENT TO PROTECT THE mOOR AND KEEP
IT CLEAN !LSO PROVIDES AN ADDITIONAL MOISTURE BARRIER
FIG
FIG
FIG
FIG
IMPORTANT:
Do not attempt this assembly with the spanner joined.
s #ONNECT THE SNAPS ON THE UNDERSIDE OF THE FLY TO THE RINGS ON SIDE OF
THE TENT 3EE FIG
s #ONNECT FOUR SHOCKCORDED 3HOOKS LOCATED AT mY CORNERS TO THE
RING AND PIN ASSEMBLIES AT BASE OF EACH POLE
s 3TAKE DOWN THE TWO PULL OUTS ON THE SIDES OF THE &LY
3EE FIG
4, ONLY
RECOMMENDATIONS:
s $URING STRONG WINDS TIE EXTRA ROPES ; NOT INCLUDED = TO THE
STORM RINGS ON THE mY AND STAKE DOWN SECURELY .OTE STAKING PATTERN
3EE FIG
s 4AKEDOWN TASK SEQUENCE
2EMOVE mY AND OPEN DOOR
$ISCONNECT HOOKS AND PEAK SHOCKCORDS
2EMOVE CLIPS FROM THE TENT POLES THEN PULL THE PINS
OUT FROM THE POLE ENDS
2%6 %
FIG
FIG
Pull out
Stake
3TORM 2ING
Stake
