Johnson Controls TM9V C Series Installation Manual Download | Manualshive

Page: 1 / 42

background image

Johnson Controls Ducted Systems

5750149-UIM-D-1219

TWO STAGE VARIABLE SPEED ECM
RESIDENTIAL GAS FURNACES

MODELS: TM9V*C Series

(96% AFUE Multi-Position)

INSTALLATION MANUAL

LIST OF SECTIONS

SAFETY   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DUCTWORK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FILTERS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
GAS PIPING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ELECTRICAL POWER  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CONDENSATE PIPING AND FURNACE
VENTING CONFIGURATION  . . . . . . . . . . . . . . . . . . . . . . . . . . 16
COMBUSTION AIR AND VENT SYSTEM  . . . . . . . . . . . . . . . . 22

START-UP AND ADJUSTMENTS  . . . . . . . . . . . . . . . . . . . . . . 30
SAFETY CONTROLS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
NORMAL OPERATION AND DIAGNOSTICS  . . . . . . . . . . . . . 36
REPLACEMENT PARTS LIST  . . . . . . . . . . . . . . . . . . . . . . . . . 39
REPLACEMENT PART CONTACT INFORMATION  . . . . . . . . 39
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
START UP SHEET  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

LIST OF FIGURES

Duct Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Combustible Floor Base Accessory  . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Furnace and Coil Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Horizontal Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Attic Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Suspended Furnace / Crawl Space Installation  . . . . . . . . . . . 7
Downflow Venting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Dimensions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Side Return Cutout Markings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Left Side Supply Gas Pipe Arrangement  . . . . . . . . . . . . . . . . . . . . . . 9
Gas Piping  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Wiring  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Two-stage Furnace with Communicating AC or HP . . . . . . . . . . . . . 12
Furnace Control Board – Communications Connections  . . . . . . . . . 13
Terminal Screw Wire Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Furnace with Variable Capacity AC or HP  . . . . . . . . . . . . . . . . . . . . 13
Thermostat Chart - Single Stage Air Conditioner with
Two Stage Variable Speed Furnace   . . . . . . . . . . . . . . . . . . . . . . . . 14
Thermostat Chart - Single Stage Heat Pump with
Two Stage Variable Speed Furnace   . . . . . . . . . . . . . . . . . . . . . . . . 15
Thermostat Chart - Two Stage Air Conditioner with
Two Stage Variable Speed Furnace   . . . . . . . . . . . . . . . . . . . . . . . . 15

Thermostat Chart - Two Stage Heat Pump with Two Stage
Variable Speed Furnace (Hot Heat Pump or Conventional)  . . . . . . . 16
Typical. Condensate Drain, Vertical Installation  . . . . . . . . . . . . . . . . 17
Upflow Configuration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Downflow Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Horizontal Left Configuration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Horizontal Right Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Home Layout   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Termination Configuration - 1 Pipe  . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Termination Configuration - 2 Pipe  . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Termination Configuration - 2 Pipe Basement   . . . . . . . . . . . . . . . . . 26
Double Horizontal Combustion Air Intake and Vent Term.  . . . . . . . . 27
Double Vertical Combustion Air Intake and Vent Term.  . . . . . . . . . . 27
Downward Venting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Direct Vent Air Intake Connection and Vent Connection   . . . . . . . . . 27
Combustion Airflow Path Through The Furnace Casing   . . . . . . . . . 28
Ambient Combustion Air  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Attic and Crawl Space Combustion Air Termination  . . . . . . . . . . . . . 30
Gas Valve  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Reading Gas Pressure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Furnace Control Board  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Wiring Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

LIST OF TABLES

Unit Clearances to Combustibles. All furnaces
approved for alcove and attic installation   . . . . . . . . . . . . . . . . . . 4
Cabinet and Duct Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recommended Filter Sizes (High Velocity 600 FPM)  . . . . . . . . . 8
Nominal Manifold Pressure - High Fire  . . . . . . . . . . . . . . . . . . . 10
Nominal Manifold Pressure - Low Fire   . . . . . . . . . . . . . . . . . . . 10
Ratings & Physical / Electrical Data   . . . . . . . . . . . . . . . . . . . . . 11
Maximum Equivalent Pipe Length  . . . . . . . . . . . . . . . . . . . . . . . 23
High Altitude Pressure Switches  . . . . . . . . . . . . . . . . . . . . . . . . 24
Elbow Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Equivalent Length of Fittings  . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Combustion Air Intake and Vent Connection
Size at Furnace (All Models)  . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Estimated Free Area  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Unconfined Space Minimum Area . . . . . . . . . . . . . . . . . . . . . . . 28
Free Area   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Gas Rate (CU FT/HR) at Full Input  . . . . . . . . . . . . . . . . . . . . . . 32
Inlet Gas Pressure Range  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Nominal Manifold Pressure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Default Blower Speeds  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Air Flow Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

These high efficiency, compact units employ induced combustion, reli-
able hot surface ignition and high heat transfer aluminized tubular heat
exchangers. The units are factory shipped for installation in upflow or
horizontal applications and may be converted for downflow applica-
tions.

These furnaces are designed for residential installation in a basement,
closet, alcove, attic, recreation room or garage and are also ideal for
commercial applications. All units are factory assembled, wired and
tested to assure safe dependable and economical installation and oper-
ation.

These units are Category IV listed and may not be common vented with
another gas appliance as allowed by the National Fuel Gas Code.

1
2
3
...
»

Summary of Contents for TM9V C Series











































Reviews:

No comments

Related manuals for TM9V C Series

Brand: York Pages: 4

Brand: Unitary products group Pages: 24

Brand: York Pages: 8

Brand: Shelter Furnace Pages: 27

Brand: Amana Pages: 15

Brand: Amana Pages: 19

Brand: Amana Pages: 19

Brand: Amana Pages: 60

Brand: USSC Pages: 28

Brand: Empire Heating Systems Pages: 16

Brand: Fire Chief Pages: 19

Brand: Heat Controller Pages: 16

Brand: Heat Controller Pages: 22

Brand: ICP Pages: 52

Brand: Unitary products group Pages: 24

Brand: United States Stove Company Pages: 24

Brand: ICP Pages: 42

Brand: Goodman Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands