background image

Jason International, Inc.  •  

 

501.771.4477  

 

 

 

Page 1 of 12

 

 

 

 

Customer Service :  800.255.5766 

“TO BE REMOVED FOR USE BY THE OCCUPANT.”

INSPECTION

Inspection of the unit prior to installation is the responsibility 

of the installer. All components are factory assembled to the 

bath and the unit is water tested and inspected prior to leaving 

Jason International, Inc. If the carton shows sign of damage, 

inspect the product before accepting and describe the problem 

on the Bill of Lading.   

Note: 

 Transportation and insurance 

from Jason’s factory are the buyer’s responsibility.

Damage sustained in transit is the responsibility of the carrier. If 

damage is discovered, the carrier must be immediately notified 

in writing with a request for a representative to inspect the 

unit. Failure of the carrier to respond should be reported to 

the seller and carrier. Always file a freight claim promptly.

The installer is responsible for insuring that the unit is free 

from defects or shipping damage. In the event of a problem, 

DO NOT install the unit. Jason International is not responsible 

for damage that might have been avoided by inspection or 

testing prior to installation.

Damage to the unit during installation will not be covered 

by  warranty  and  is  the  responsibility  of  the  installer.  ALL 

WARRANTY CLAIMS ON ACRYLIC SURFACE DAMAGE 

MUST  BE  MADE  PRIOR  TO  INSTALLATION.  Inspect 

OwNer’s MaNual

forma™ air-whirlpool Baths

INsTallaTION, OPeraTION, aND MaINTeNaNCe

49-1000-016

Date   04/08

Table 1 - Specifications

Jason International, Inc.

 

8328 MacArthur Drive

North Little Rock, AR 72118

www.jasoninternational.com

OwNer’s reCOrD

Dealer: 

Date Purchased: 

Date Installed: 

Installer: 

PlaCe serIal NuMBer CarD wITh 

PrODuCT CONfIguraTION IN ThIs BOx

CAUTION: DO NOT LIFT OR HANDLE THE BATH BY ITS PLUMBING.

plumbing  and  bath  surface  for  missing  or  damaged 

components. Alert your dealer of any discrepancies.

To protect the unit from damage keep the bath in the carton 

until ready for installation.

Model

Overall

Dimension

L x W x H (in.)

Operating

Capacity

gal

Blower

120v /

240v hP

Pump

120v /

240v hP

Min. Size

access

w x h 

(in.)

floor

Loading

lbs/ft

2

AIR-WHIRLPOOL

AC630

72 x 36 x 22

45

1

1.5

36 x 17

56.7 lbs

AC635

72 x 42 x 22

56

1

1.5

36 x 17

52.9 lbs

CN550

60 x 60 x 22

66

1

1.5

36 x 17

51.9 lbs

DA500

60 x 60 x 20.5

55

1

1.5

36 x 17

49.5 lbs

RC630

72 x 36 x 22

50

1

1.5

36 x 17

52.5 lbs

RC635

72 x 42 x 22

58

1

1.5

36 x 17

52.9 lbs

RE525

60 x 30 x 20.5

38

1

1.5

36 x 17

61.6 lbs

RE527

60 x 32 x 20.5

39

1

1.5

36 x 17

59.5 lbs

RE553 

66 x 36 x 22

47

1

1.5

36 x 17

55.2 lbs

RE630

72 x 36 x 22

53

1

1.5

36 x 17

54.1 lbs

Содержание forma Series













Отзывы: