WARNING! This device is not intended for use with
emergency exit fixtures or emergency exit lights.
WARNING! Permanent damage to the low voltage 14VAC
lamp will occur if installed on a 120VAC circuit.
WARNING! Remove warning label from PureWhite lens
before installation.
ATTENTION 14V PUREWHITE OWNERS!
DANGER!
Risk of electrical shock or electrocution
WARNING!
Read this before attempting installation
Rated Lamp Life
Safety Precautions
IMPORTANT NOTE:
Installation
PureWhite
TM
2 Pool Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL LAMPS
Model #s: LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-P2-WHT-12-SQ, LPL-P2-WHT-120-SQ
Light housing compatibility
Compatible NRTL light housings
include:
Hayward
®
Astrolite
™
SP058 Series
Hayward
®
Astrolite
™
SP058 Series Housing -
Use replacement gasket specified by manufacturer.
Sta-Rite
®
SwimQuip
™
Series 0508
Sta-Rite
®
SwimQuip
™
Series 0508 -
Requires installation of J&J Gasket
#LPL-G-S. Included with LPL-P2-WHT-12-SQ and LPL-P2-WHT-120-SQ.
Jacuzzi
®
Full Moon
™
Jacuzzi
®
Full Moon
™
-
Use replacement gasket specified by manufacturer.
Pentair
®
Amerlite 784 Series
Pentair
®
Amerlite 784 Series -
Requires installation of J&J Gasket #LPL-G-P.
Included with LPL-P2-WHT-12 and LPL-P2-WHT-120.
Gasket compatibility
™
The product warranty is voided if the proper gasket is not installed.
See the “Warranty” section at the end of this manual for details.
STEP 1
Remove light housing from niche
Figure 1: LPL-P2-WHT
PAGE 1
J&J Electronics
•
6 Bendix, Irvine, CA 92618 USA
•
800.735.4553
•
949.455.4460
•
www.jandjpoolspa.com
STEP 2
Remove old lamp
PureWhite Replacement LED In-Ground Pool lamps are available in 14VAC (low
voltage) and 120VAC models as indicated on the product packaging. Each lamp has
a screw-in Edison base.
The warning label is placed on top of a special optical diffuser designed to maximize
the light projection of the PureWhite lamp. When you remove the label, a protective film
will come off with it. Once the warning label and protective film have been removed,
do not allow the diffuser decal underneath to be scratched.
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness. To verify the
voltage, at the lamp socket, measure the open circuit voltage (no lamp in the socket).
Set the transformer tap to 14.0VAC.
Your PureWhite lamp is not an ordinary light bulb. It is a valuable electronic device that
is not designed to come in direct contact with water. An improper installation that
results in water leakage into the pool light housing can permanently damage the
PureWhite lamp.
Please read these installation steps and the original
manufacturer’s pool light installation manual carefully before proceeding.
Make sure power to the pool light is turned off at the circuit breaker. Carefully remove
the existing light housing from the niche assembly and place it on the pool deck. There
should be enough power cord to do this easily. If there is not enough power cord to
allow the light housing to reach the pool deck surface, call your local pool service
company.
Access the old lamp according to the original manufacturer’s pool light installation
manual. Remove the screws and/or loosen the clamp that holds the face plate and lens
in place. Carefully remove the lens from the pool light housing. Take care not to
damage the surface of the light housing body that makes contact with the rubber
gasket.
WARNING! Verify that your PureWhite lamp voltage rating
(120VAC or 14VAC) matches your electrical system’s
voltage requirements before proceeding with installation.
The illumination generated by the PureWhite Replacement LED In-Ground Pool lamp is
based on Light Emitting Diode (LED) technology. The average expected lamp life is
rated up to 50,000 elapsed time hours under normal operating conditions.
[Temperature: 33°F to 95°F (1°C to 35°C), Humidity: 0-95% non-condensing].
•
Do not open, service or tamper with any internal component of the PureWhite
Replacement LED In-Ground Pool lamp. Doing so will void the warranty. Follow
each instruction in this owner’s manual and pay careful attention to all warnings.
•
Do not directly expose or immerse the PureWhite Replacement LED In-Ground
Pool lamp in water without containing it in a proper, watertight, NRTL
(nationally recognized testing laboratory) pool light housing and niche
assembly.
•
Handle the PureWhite Replacement LED In-Ground Pool lamp with care. Be
careful not to drop the unit.
PureWhite lamps are recommended for installation by a qualified pool professional.
The installation steps in this owner’s manual are intended as guidelines. For specific
instructions on how to replace a pool lamp, please refer to the original manufacturer’s
pool light installation manual before proceeding.
PureWhite Replacement LED In-Ground Pool lamps must be installed in a compatible
NRTL pool light housing.
LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-P2-WHT-12-SQ, LPL-P2-WHT-120-SQ
•
Keep the pool light housing dry.
Always disconnect power to the pool light at the circuit breaker panel before
attempting to service the lamp. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer’s pool light installation
manual before proceeding. As with any electrical device, installation and service
should always be performed by a qualified
individual. This device is not intended for
use in anything other than in-ground pools.
PureWhite Replacement LED In-Ground Pool lamps offer superior, bright white illumination for your pool. This owner’s manual contains important information
on installing and using your new PureWhite Replacement LED In-Ground Pool Lamp. Please read it carefully and keep it in a safe place for future reference.
