Jameco Electronics Freeze the Dizz Скачать руководство пользователя

Страница: 1 / 31

Freeze the Dizz | Jameco Part No. 2161431

This project is based on a childre

n‟s a

rcade game. Twenty LEDs are placed on a ring

and each takes turn to light up forming a rotating light spot. If a push-button switch is

pressed, the light spot freezes. If the light spot happens to land on the winning position,

a buzzer is triggered. The rotating speed is adjustable by a speed dial.

See a video demonstration here:

http://www.youtube.com/watch?v=3dcK2xYX3t4

You can learn

basic building blocks of electronics circuit such as flip-flop (CD4013),

counter (CD 4017), one-shot and 555 oscillator with this project. You can see how they

are put together to achieve the circuit operations desired

. You will test each individual parts

of the circuit to understand the roles of each IC and major components.

Experience Level: Intermediate | Time Required: 12-24 Hours

Содержание Freeze the Dizz
































Результаты поиска

Содержание Freeze the Dizz

Отзывы:

Похожие инструкции для Freeze the Dizz

Бренды по названию

Популярные бренды

Jameco Electronics Freeze the Dizz, Инструкция по эксплуатации

Результаты поиска

Содержание Freeze the Dizz

Отзывы:

Похожие инструкции для Freeze the Dizz

Бренды по названию

Популярные бренды