background image

Magic 

C

olor

PART NO.

 2193838

 

Magic  color  is  a  guessing  game.  With  this  game  you  can  surprise  your  friends  and  leave  them  with  amazement,  how  the  game

 

guesses what they have in their minds. Only two selections require from the user to guess the game the color combination that is in

 

his mind. The game has the following parts: 

1.Matrix rgb board with five rows and five columns of leds.
2.6 buttons. One button is to starting a new game and the other five is to playing the game. Its button (the group of five buttons) is
under a specific column of the matrix board. So under the first column of matrix board exists one button, under the second column of
matrix board exists one button e.t.c.

I will describe the operation of the game in the following steps:
1.The user presses the starting button and leds on the matrix board take different colors combinations between them. For example, a
 led can be fixed in red or red color with green that toggle. 
2.The user memorizes one led with the combination of color.
3.The user presses the button of a column in which exists the memorized led.
4. The firmware calculates and changes all the places of colors combinations with respect of  specific algorithm.
5.Revision of step 3.
6. Finally the firmware guesses the memorized selected combination color of the
 user by making all leds to light with this same color combination. 

Time Required: 15-20 Hours  depending on experience

Experience Level: Intermediate

Required tools and parts:

Soldering iron and solder
Wire stripper/cutter and basic hand tools

 

Digital multimeter
Lighter
Programmer for avr controllers
Drill
A hot glue gun loaded with a glue stick

 

Blue marker or black
Screwdriver
Ruler

Bill of Materials:

Qty

Jameco SKU

Component Name

1

2139111

MCU 8-Bit ATmega AVR RISC 8KB Flash 5 Volt 28-Pin PDIP

For longer life of the battery the newer controller from Atmel  

(

ATMEGA8A-16PU

)

 

is recommended

(http://www.hqew.net/product/ATMEGA8A$2d16PU_15D43851132442DB86251B9A6A30D2D9.html)

or

(http://shop.tuxgraphics.org/electronic/detail_atmega8.html)

or

(http://www.ebay.com/itm/50PCS-ATMEGA8A-PU-DIP-28-Microcontroller-MCU-AVR-NEW-DATE-CODE-12-/300766358016)

25

2128500

LED,RGB,WATER CLEAR,T1-3/4,2.0,-3.5VF@20mA,COMMON ANODE,25DEG

11

25523

.1 uF 50 Volt Monolithic Capacitor

2

158289

Capacitor Radial 470 uF 25 Volt 20% 105c 10x16x5mm

Summary of Contents for 2193838











Reviews: