background image

Model 37010-Series

Model 

37010-Series

ELECTRIC MARINE TOI LET 
Push Button Operation

FEATURES

• White Vitreous China Bowl Available in Two Sizes
• Baked enamel seat & cover -

soft close seat option available on regular bowl models

• Flexible Impeller Flush Pump
• Permanent Magnet Type Motor, Fully Enclosed, with

Stainless Steel Shaft

• High Capacity Waste Macerator and Bowl discharge Pump
• Built-in Back Flow Preventer

V

Corrosion resistant material for marine use

ARIATIONS

MODEL NUMBER 

DESCRIPTION

37010-3092 

Compact Bowl 12V 

37010-3094 

Compact Bowl 24V 

37010-4092 

Regular Bowl 12V 

37010-4192 

Regular Bowl 12V, Soft Close Seat/Lid 

37010-4094 

Regular Bowl 24V 

37010-4194 

Regular Bowl 24V, Soft Close Seat/Lid

INSTALLATION

The Jabsco electric toilet may be installed above or below

the waterline. Flush pump is self-priming with a vertical lift

up  to  4  feet;  discharge  macerator  pump  can  operate

against a vertical head up to 4 feet (1.2m).
Inlet and outlet seacocks should be easily accessible and

be positive shut off valves. If seacocks cannot be con ve -

nient ly operated from toilet location, install suitable shut off

valves for inlet and discharge connections.
Base assembly may be moved 90° to accommodate con -

nec tions and provide accessibility for servicing.
Surface where toilet is mounted should be flat to prevent

distortion of toilet base.
PLUMBING CONNECTIONS - Connect inlet hose using

3/4" (19mm) ID hose. Make sure all inlet connec-tions 

are airtight and free of sharp bends or restrictions.

 

Do  not  connect  the  toilet  to  the  vessels

potable water for its source of supply. To do so can result in

contamination of potable water supply. If fresh water is pre-

ferred for flushing, provide a separate fresh water tank to

supply water to the toilet only.
DO NOT CONNECT INLET HOSE TO A PRESSURIZED

WATER SYSTEM.

Flood hazard.   If toilet is installed below the 

waterline or may be below the waterline at any 

angle of heel or trim, it must be installed with 

properly positioned vented loops.  Failure to do 

so can result in flooding which can cause loss 

of property and life.

WARNING

!

CAUTION

!

Connect  1"  (25mm)  or  1-1/2"  (38mm)  hose  to 

discharge hose to discharge port (Adaptor

 

98023-0080 is 

included to convert discharge port to 1-1/2"ID hose), 

and  make  suitable  connection  to  holding  tank 

orother  discharge  system.  Avoid  sharp  bends  or 

restrictions.For  above  waterline  installations,  a  check 

valve may haveto be instal-led in the flush water intake 

line  to  ensure  rapidpump  priming.  To  retain  water  in 

bowl,  make  a  loop  in  the

 

discharge  line  about  8  inches 

(200mm) above base of bowl.

If the toilet is, or can be, below waterline at any normal(in-

cluding static) attitude of vessel heel and/or trim, a 3/4" 

(19mm) Vented Loop Fitting must be installed in the 

length of hoseconnecting the flushing pump to the inlet 

seacock. TheVented Loop Fitting must be positioned so it 

remains at least 8" (200mm)* above the waterline at all 

angles of heel and trim.In some installations when a 

vented loop is installed in theintake hose, the flushing 

pump primeability and flow char-acteristics are reduced 

and  may  adversely  affect  toiletfunction.  To  restore 

pump  performance,  connect  a  solenoid

 

valve 

(Jabsco  No.  37068-

2

000)  to  the  vent  air  inlet  to 

inter-rupt the air supply during the flush cycle. The 

brass port ofthe solenoid valve (remove plastic filter if 

attached)shouldbe  connected  to  the  vent  inlet  with 

3/16" hose and thesole-noid  wired in parallel with the 

toilet motor. See diagram below.

www.PumpAgents.com - Click here for Pricing/Ordering for Pumps and Parts

Jabsco Pumps 37010-4194

Reviews: