JABLOTRON
ALARMS
a.s.
Pod
Skalkou
4567/33
46601
Jablonec
n.
Nisou
Czech
Republic
www
.jablotron.com
||
|
PT-P700 Label printer
The PT-P700 printer is an accessory of the
JABLOTRON 100
system.
Using this printer you are able to print labels for control segments of
access units (keypads) at installation. The printing is possible straight from
F-Link software version 1.2.0 or higher
from the access module internal
settings. The drivers have to be installed for the proper functioning of the
printer. The printer can also be used for printing labels using P-Touch Editor
Lite software saved inside the printer memory. In this case no drivers are
required.
PT-P700 label printer – hardware
description
Figure 1: 1 – Upper panel, 2 – Editor Lite LED, 3 – Editor Lite button,
4 – Outlet for tape, 5 – Feed-in and cut-off button, 6 – Power LED indicator,
7 – ON/OFF button, 8 – Battery cover, 9 – MiniUSB port,
10 – Connector for mains power adapter, 11 – Tape cover
Tape box installation
1. Make sure that the printer is turned off. Open the tape cover (11)
marked by the
ÄŹ³
symbol, move away from the arrow direction.
2. Insert the tape box. For printing labels always use the tapes
supplied by Jablotron Alarms (PT-Tape02-BW, width of 12 mm).
3. Ensure that the end of the tape has been inserted correctly. If the
tape is loosen, use a new tape. It could damage the printer.
4. Before you close the tape cover, make sure that the tape cover tab
is open. It is not possible to close the tape cover if the tab is
pressed.
5. When the tape box has been inserted, turn on the printer by
pressing the power button (7), see the following chapter. Then
press the feed and cut button (5). The tape is aligned and cut off.
The PT-P700 printer power connection
Use a standard (AD-E001 EU) mains adapter (in the accessories),
plug the mains power adapter into the socket (10) on the rear side.
The printer can also be powered by 6 AA (LR6) batteries. Insert the
batteries into the battery holder under the battery cover (8). Take care
of the polarity when inserting them. When you change the batteries
always replace all of them new.
Note
: The printer is automatically turned off when there is no activity
for 20 min because of power saving.
Connecting the printer via USB and label
creating options
1. Connect the printer´s USB mini port (9) to your PC by the supplied USB
cable.
2. Turn on the printer (7), the green status LED lights up (6).
3. The printer boots to label printing mode from F-link 1.2.0 software and
higher, see the following chapter. If you need to use the printer without
F-link software, continue to the chapter
Creating labels for JA-100
keypads using P-Touch Editor Lite.
Creating labels for JA-100 keypads using
F-Link software 1.2.0 and higher
1. Check if you have installed F-Link software 1.2.0 or higher on
your PC.
2.
Make sure the Editor Lite indicator (2) isn´t lit. If it is, change the printer
mode by long pressing of the Editor Lite button (3).
3. Install the drivers for the printer from the supplied CD. The device
has to be visible in
Printer manager
as a Brother PT-P700. When
the CD is inserted into the PC, a main menu pops up. Click on
Standard Installation,
an installation wizard will guide you through
printer installation. (Start this application manually if the system
doesn´t show the main menu by clicking on the file
Start
on the
CD).
4. We recommend restarting the PC when the drivers have been
installed.
5. The Brother PT-P700 printer is visible in the system when the
restart has been done.
6. Now the F-link software 1.2.0 or higher is ready to print the
segment labels from the internal settings of the access modules.
Use the option
Print labels
. When the window with predefined
labels appears, then select the printer PT-P700 and also check the
label width (12 mm) in the printing options.
7. When confirmed the label is printed.
Creating labels for JA-100 keypads using
P-Touch Editor Lite
In the Editor Lite mode it is not necessary to have installed drivers
and it is possible to print the labels without the F-link software.
By long pressing of the Editor Lite button (3) change the printer
mode – the Editor Lite indicator (2) lights up. The printer appears as an
external disc called PT-P700, which includes P-Touch Editor software
(PTLITE10.EXE). Start it.
Recommended format settings for JA-100 keypad segments:
1. Set the label height to
12 mm
.
2. Right-click on the editing field and open
Options
. Choose
Margins / Small
.
3. Set the label length to
71 mm
.
4. Set the font to
Arial
, set the size to
23.0
and confirm (Enter).
5. Set
Boldface
and
Left alignment
.
6.
Edit the text.
Note
: After these settings edit the text without clicking into the editing
field. Otherwise the font will be set to the default of 28.
When the text has been prepared, set the automatic cutting of the
label to a pre-set length for when printing is finished:
7. Open the
Printing preferences
in the right corner next to the
printer icon.
8. Choose
Printing preferences / Automatic cutting
9. Confirm
the number
of required labels and click on
.
Recommendation
: all settings can be saved in a file and used later as
an example for future editing.
Inserting the label into the JA-100 keypad
segment
When the label with text is finished,
insert it into the segment in the way
shown by the below illustrations.
Disconnecting
the PT-P700 printer
1. Quit the P-Touch Editor Lite
application by clicking on the symbol
in the rightmost corner of the
software.
2. If you want to disconnect the printer
from the PC, click on the PC tray icon
used for the safe removal of USB
devices and select the option to remove it.
3. When
it is possible to disconnect the printer from the computer
,
turn off the P-Touch printer and disconnect the USB cable.
Technical specifications
Dimensions (w x l x h)
78 x 152 x 143 mm
Weight, with no batteries and no tape
710 g
Power
mains adapter AD-E001 EU (in accessories)
6 x alkaline batteries AA (LR6) / 1.5 V (not in accessories)
USB Port
USB mini B (in accessories)
Tape box for segment label printing (in accessories)
12mm (w), 8m (l)
Tape box for different printing other than segments (in accessories)
24mm (w) / 3m (l)
Note
: The printer and this manual are provided as accessories for
creating segment descriptions for JA-100 RFID readers and keypads.
For different applications use the original manual from the printer
manufacturer.
Note: Although this product does not contain any
harmful materials we suggest you return the product
to the dealer or directly to the producer after use. For
more detailed information visit www.jablotron.com
Distribution: Jablotron Alarms a.s., www.jablotron.com
PT-P700 Label printer
1 / 1
MZZ26400
