The JA-60V wireless outdoor PIR detector
The JA-60V wireless outdoor PIR detector
1 / 2
MEB52102
The JA-60V wireless outdoor intruder detector is designed to detect human
body movement in a protected area. It supplements a double-zone PIR
sensor produced by Optex with a Jablotron transmitter enabling the detector
to be used within the JA-60 systems. The optical part of the detector has 2 PIR
sensors and high immunity to false alarms and the detection of small animals.
The detector includes an Anti-masking function – protection against covering the
view and it also has two tampers (front and back) built in. They immediately
report opening the detector or attempting tampering. The detector does a self-
test periodically and sends its status by a connection test to the control panel.
The detector should be installed by a trained technician with a valid certificate
issued by an authorised distributor.
Installation
Choose a proper place for detector installation according to the following:
1. The detector has to be installed onto a vertical wall (in a position where
its bottom surface is parallel to the watched zone).
2. The detector should be installed 0.8 – 1.2 m above the ground.
3. The best movement detection is provided when the detection beams
intersect.
4. No other moving objects (bushes, trees, high grass, air-conditioners, etc.)
should be situated in the field of sight of the detector. Avoid direct action by
strong sources of light (sun reflections, etc.).
Note
: If multiple JA-60V detectors are used, they don´t have to be installed
face to face with each other and its recommended to install them with a
minimum 1 m distance.
Procedure:
1. Unscrew the locking screw placed on bottom of the upper cover of the
detector (1) and remove the detection part cover (1).
2. Unscrew the 2 screws which hold the detector´s main board (2) and
pull it out by tilting as you pull it out.
3. Remove the battery holder.
4. Remove the rear box cap (5).
5. Unscrew the 2 screws which link the rear cover (3) with the mounting
plate (4).
6. The detector can be mounted onto a level mounting place by the 2
screws through the mounting plate (4). Or it can be mounted on timber
by ties.
7. Put the detectors parts back together in the opposite order when it´s
finally fixed to the mounting place (4).
Warning
: Do not touch the detector sensing face during handling
.
1
2
3
4
5
Fig. 1.: 1 – front cover, 2 – detector main board, 3 – rear cover,
4 – mounting plate, 5 – rear cover cap
Fig. 2.: Detector installation. Standard installation and fixing by ties.
Enrolling the detector to the system
The signal transmitter for wireless communication is located in the back
plastic part under the optical part of the detector. The detector is powered
by the batteries as well. Always use just AAA batteries from the same
producer and if replacement is needed change both of them. The correct
position of the batteries is indicated on the bottom of the plastic battery
holder.
Enrollment procedure to the system:
a. Read the installation manual of the receiving unit before you insert the
batteries into the detector.
b. There must be a radio module installed in the control panel.
c. Open the enrollment mode on the receiving unit.
d. Insert the batteries (mind the correct polarity). When the first battery
has been inserted into the battery holder an enrollment signal is
transmitted to the control panel and the detector is enrolled to the
selected position. Assemble the detector.
e. By DIP switch no.1 set the reaction to detected movement (ON =
Instant, 1 = delay). Leave DIP switch no.2 in the ON position.
Fig. 3 – A view of the JA-60N transmitter
Setting up the optical part of the detector
The optical part of the detector includes 2 PIR sensors with AND logic.
They detect movement in two planes. The detecting angle of the lower PIR
sensor can be adjusted to a wide angle range. The alarm signal is triggered
if only both detecting planes are triggered at the same time. By shifting the
lens set up the tilt of the lower detecting plane according to the following
picture and table.
Fig. 4.
The following table represents the values included in the figure:
Position
Maximum range of the lower detecting
part
Average value
see following
warning:
1
12 m
10 to 17 m
2
8.5 m
7 to 12 m
3
6 m
5 to 8.5 m
4
3.5 m
3 to 6 m
5
2.5 m
2 to 3.5 m
Table
1.
Warning:
The maximum detection length of the lower detection plane may vary
as above due to environmental thermal conditions. This must be taken into
consideration during detection range adjustment.
Fig. 5.
The detection area angle is 90°. The direction can be adjusted from
position A – G by rotating the detector´s plastic part. Each step is
circumscribed. The detector lens covers the whole angle of 180° - therefore
it does not require any adjustment.
