![background image](http://html2.mh-extra.com/html/jablotron/ja-120pc/ja-120pc_quick-start-manual_3152925001.webp)
JABLOTRON
ALARMS
a.s.
Pod
Skalkou
4567/33
46601
Jablonec
n.
Nisou
Czech
Republic
www
.jablotron.com
||
|
JA-120PC BUS PIR motion detector with a camera
JA-120PC BUS PIR motion detector with a camera
1 / 2
MMP51105
The JA-120PC is a component of the JABLOTRON JA-100 system.
It serves for the detection of human movement in building interiors and
visual alarm confirmation. The camera takes colour photos with
a resolution of up to 640 x 480 pixels. Taking photos is triggered
by detecting human movement; this is so that the reason for the alarm
is always recorded. The camera is equipped with a visible flash for
taking photos in the dark. The images are saved in the internal memory
of the detector and then they are forwarded to the control panel.
And from the control panel they can be sent to MyJABLOTRON or ARC.
The detector can also take a picture if it is required. The detector takes
one position in the system and should be installed by a trained
technician with a valid certificate issued by an authorised distributor.
The photo-verification can be used only after the
registration of the system to MyJABLOTRON
or with subsequent ARC service.
Installation
The detector can be installed onto a wall or in the corner of a room.
There should be no objects which quickly change temperature (electric
heaters, gas appliances, etc.) or which move (e.g. curtains hanging
above a radiator) or pets in the detector´s field of sight. It is not
recommended to install the detector opposite windows or floodlights
or in places with over-intense air circulation (close to ventilators, heat
sources, air conditioning outlets, unsealed doors, etc.). There should
be no obstacles in front of the detector which might obstruct its view.
When connecting the detector to the system BUS,
always switch the power off.
1.
Open the detector cover
(by pushing the tab (4)).
Avoid touching the PIR
sensor inside (14) – you
could damage it.
2.
Take out the PCB –
it is held by a tab (9).
3.
Punch through the holes for
the screws and the cable
in the plastic base.
The recommended detector
installation height is 2.5 m
above the floor.
4.
Insert the BUS cable and
attach the plastic base
to the wall using screws
(vertically, with the cover
tab facing downwards).
5.
Re-insert the PCB and
connect the BUS cables
to the terminals (11).
Figure: 1 – flash for illumination; 2 – camera lens; 3 – PIR detector lens;
4 – cover tab
Figure: 5 – Camera module; 6 – connecting cable; 7 – production code;
8 – red LED; 9 – PCB tab; 10 – yellow LED; 11 – BUS terminals;
12 – BUS cable; 13 – tamper contact; 14 – PIR sensor;
15 – Micro SD memory card; 16 – yellow LED of micro SD card.
6.
Proceed according to the control panel installation manual. Basic
procedure:
a.
When the device is switched on, the yellow LED (10) starts
flashing repeatedly to indicate that the module has not been
enrolled into the system.
b.
Go to the
F-Link
software, select the required position
in the
Devices
window and launch the enrollment mode
by clicking on the
Enroll
option.
c.
Click on the option
Scan/add new BUS devices
, select
the JA-120PC detector and double click to confirm –
the detector is enrolled into the selected position and the yellow
LED (10) goes off.
d.
If the detector is enrolled as a first camera PIR or the control
panel is not connected to MyJABLOTRON, F-link shows
a dialogue window with the question about enabling data
transfer. We strictly recommend enabling this option with
the agreement of the customer and confirming this acceptance
by recording it in the system service log with his signature.
Note: If the transmission is not enabled, images will be saved
only in the internal memory of the detector and the control
panel. Then it is impossible to send the photos
to MyJABLOTRON or to ARC.
7. Close the detector cover.
Notes:
−
The detector can also be enrolled into the system by pressing
the cover tamper sensor (13).
−
The detector can also be enrolled into the system by entering its
production code (7) in the F-Link software (or with a barcode
scanner). All numbers under the bar code must be entered (1400-
00-0000-0001).
−
To remove the detector from the system, erase it from its position
in the control panel.
−
To meet the EN 50131-3 standard it is necessary to secure
the cover tab (4) with the supplied screw.
Detector internal settings
Settings can be set by
F-Link
software –
Devices
tab. When
at the detector position, use the
Internal settings
option to open a dialog
window where you can configure the settings (
*
default settings):
LED movement indication:
*Enabled
; allows you to disable movement
indication with the red LED.
PIR immunity level:
Defines false alarm immunity. The
*Standard
level
combines basic immunity with a rapid reaction. The Increased level provides
higher immunity but the detector reaction is slower.
PG output reaction:
select PG outputs, by whose activation picture
taking is triggered (
*No
, camera does not react to PG). For further info see
Installation recommendations, cautions.
PG-state-triggered picture taking:
No flash, *With flash
Photo taking during entrance delay: *No flash, With flash
Photo taking during alarms: No flash, *With flash
Flash intensity: Low, *Medium, High –
in the case of overexposed scene
with a flash (e.g. in a small room) the intensity of the flash can be reduced.
For larger spaces it can be increased.
Caution:
If there are more detectors
with the ability to simultaneously take a photo with high intensity flash
in the system (e.g. when PG output is activated) there is a risk of a one-time
high consumption from the BUS, which may cause a short-term power
outage. We therefore recommend checking and counting the total
consumption.
Increased number of photos during alarm:
When enabled, 3 photos
are sent instead of 2 during each alarm event, that means more data
transfer between the detector and the control panel and between the control
panel and MyJABLOTRON or ARC. This option is for specific markets
so we don’t recommend enabling by default.
Send pre-alarm photos:
When enabled, the photos are sent also during
an unconfirmed alarm, if the repeated or confirmed reaction is set. During
each entrance delay, if the detector is triggered up to 2 photos can be sent
even in case of successful unsetting of the system.
This option will cause a significant increase of the data amount transferred
to MyJABLOTRON. In case of alarm being not unset (an alarm is triggered)
the photos are sent automatically regardless of this option.
Test:
takes a test picture with a flash and F-link shows it. When the
Detail
button is pressed, F-Link shows the picture with a 640 x 480 px resolution.
Camera and basic reactions
The processing of how the camera takes pictures depends
on the settings in the
F-link
software –
Devices
tab. Choose
the Reaction
button on a particular detector line.
Instant:
During the alarm state the camera can be triggered 3 x (then
it is auto-bypassed). Every movement takes 3 photos maximum, this