INSTALLATION INSTRUCTIONS
:
BM001/BM003
1. Preparation
(1.1) Due to the sliding cover of the Bio-Matic™, an
minimum clearance of 5” must exist above the lock
mounting hole.
(1.2) Check (Fig. 1) to determine if the lock lever direction
is corresponding to the door left-handed or right-handed.
(1.3) This Bio-Matic lock works on doors with a thickness
between 1.5” to 2.36”.
2. Install Latch and Plate
In the package, you will find two Latch Backsets. The short
one is 2-3/8". The long one is 2-3/4".
(2.1) Determine the Backset by measuring the distance
from the edge of the door to the center of the hole.
(2.2) The end of the Backset should be in the center of the
hole when Backset is fitted from the side of the door.
(2.3) Insert Backset with angled side of bolt facing outside.
Fasten with 2 Flat Head Screws.
(2.4) On the other side, use another 2 Flat Head Screws to
secure the Strikeplate on the wall.
3. Install Lock Units
(3.1) Remove the Cover of the Interior Lock Unit.
1. Loosen the ring with a “Y” Spanner by turning counter-
clockwise.
2. Remove both the ring and the cover from the Lock Unit.
(3.2) Install the Interior and Exterior Lock Unit.
1. Unscrew the 2 Connection Screws to separate the
Interior and Exterior Lock Unit.
2. Insert the Exterior Lock Unit with protector and the cable
through the door hole. Then hold tight.
3. With the cover removed, insert the Interior Lock Unit with
protector on the other side, with the battery compartment
on top.
4. The extension from the back of the Exterior Lock Handle
should fit in a star shape hole at the back of the Interior
Lock Handle.
5. Run the cable through the hole under the battery
compartment.
(3.3) Insert batteries and connect the power cable.
1. Insert 4 AA batteries into the battery compartment. Make
sure they are in the correct directions.
2. Plug in the cable into the bottom of the battery
compartment.
3. Align and fasten 2 Connection Screws to secure the
Lock Units.
(3.4) Re-install the cover of the Interior Lock Unit.
1. Insert the cover and the ring back to the Interior Lock
Unit.
2. Use the “Y” Spanner to tighten the ring by turning
clockwise.
4. Testing
(4.1) The handles should not block the way of entrance or
when opening the doors.
(4.2) Slides open the protective cover. You should see a
blue light at the background of the scanner window.
Bio-Matic™ Fingerprint Door Lock
Single-Latch
User Manual
DEFAULT MASTER CODE:
A default master code is set when the Bio-Matic is
manufactured. The passcode is
“11111111”
. The master
code is always an
8-digit
number and you will need to use
the master code for all operations.
1. Modifying Master Code:
1. Slide open front cover and press “0” then “*”
2. Enter Current Master Code
3. Enter New Master Code
4. Repeat New Master Code
5. Press “#” when finish
6. New Master code is accepted when you hear a
“BEEP”
7. If you hear 3 “BEEPS”, please repeat step 1 to 5, New
Master Code is NOT accepted
2. Reset Master Code
If for any reason you could not remember the master
code, you can set it back to the manufactured default
code
“11111111”
by following the steps below
Note: This will erase all codes including User Numbers,
Fingerprints and Passcodes
1. Uninstall the Interior Lock Unit
2. Use the “Y” Spanner to remove the ring and the cover
of the Lock Unit by turning counter-clockwise
3. Disconnect the power cable from the battery
compartment. Then press and hold both “1” and “2” on
the key pad spontaneously while you reconnect the
power cable. The default code is successfully set when
you hear a “BEEP”.
OPERATIONAL INSTRUCTIONS:
1. Registering Fingerprints
(2.1)
Register with User Number
1. Slide open front cover and press “1” then “#”
2. Enter Master Code
3. Enter 3-digit User Number, then press “#” to confirm
4. Put finger tip on the center of the scanner when blue
light is on. Lay flat and hold firmly until you hear a
“BEEP”.
5. Repeat step 1 to 4 above to enter another user
6. If you hear 3 “BEEPS”, the fingerprint is not
recognized, please repeat step 1 to 4
To register user# 123 with default master code 11111111
Enter sequence on keypad: 1, #, 11111111, 123, #
When the scanner lights up, put finger on the scanner
to
register the fingerprint for user# 123
(2.2)
Register without User Number
1. Slide open front cover and press “1” then “#”
2. Enter master code
3. Press “#” to confirm
4. Put finger tip on the center of the scanner when blue
light is on. Lay flat and hold firmly until you hear a
“BEEP”.
5. Repeat step 1 to 4 above to enter another user
6. If you hear 3 “BEEPS”, your fingerprint is not
recognized, please repeat step 1 to 4
To register a user with default master code 11111111
Enter sequence on keypad: 1, #, 11111111, # When the
scanner lights up, put the FINGERPRINT to register.
IMPORTANT: If you have trouble installing the Bio-Matic
Door Lock or you have additional questions or concerns,
please contact iTouchless Customer Service at 1-800-
660-7978 Monday to Friday from 9:30am to 5:00pm PST.
DO NOT RETURN THIS ITEM TO THE STORE OR
