![background image](http://html1.mh-extra.com/html/invotel/audioimage-sx9300/audioimage-sx9300_user-manual_2085613001.webp)
Warranty
This product is warranted against defects for a period of Five (5) years from the date of original
invoice. We will repair/replace the product with no charge for parts or labor within this time. To
obtain warranty service the product needs to be returned freight prepaid by the customer with a
copy of original invoice. This warranty does not apply if in the sole opinion of Innovative
Telecommunication Technology, the product has been tampered with or damaged by lightning
or any other acts of nature, misuse, neglect or unauthorized service.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR OTHERWISE,INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OR MERCHANTIBILITES OR FITNESS FOR A SPECIAL PURPOSE.
IN NO EVENT SHALL INNOVATIVE TELECOMMUNICATION TECHNOLOGY (INVOTEL) BE
LIABLE FOR LOSS OF PROFITS OR BENEFITS , INDIRECT, SPECIAL, CONSEQUENTIAL
OR OTHERWISE ARRISING FROM ANY BREACH OF THIS WARRANTY OR OTHERWISE.
®
1112 Montana Ave Suite 250 Santa Monica, CA 90403 USA
Toll-Free: 800-747-0708 Tel: 310-899-0078 Fax: 310-899-0227 http://www.invotel.com
User Manual
AudioImage
™
SX9300
Rev 01
Digital Audio System Player/Recorder
•
Connect your PC “speaker out” or CD player headset jack to the “Audio
IN” jack of the SX9300 using the provided 3.5mm to 3.5mm audio cord
& the “Y” patch cable
Note: do not use “line out” jack on PC/CD player.
•
Plug one end of the RCA audio cable into the 8
Ω
Red RCA connector
of Player, Plug the other end of the audio cable into your PBX phone
system RCA connector usually labeled as “MOH”.
(If you have regular Non-PBX telephones, plug the other end into the Music-On-Hold
adapter “Audio In” RCA connector instead)
•
Set the Volume to mid level by rotating the Volume control on the
SX9300 player clock wise as shown.
•
Set the BANK switch to 1
•
Plug the included AC adapter.
(110V AC to 9V AC)
•
Unplug the power connector wait 30 seconds then plug it back
in. make sure the connector is plugged in securely. Be sure to
observe the LED lights are dancing with volume up.
2.
No audio on hold
•
Check audio cord; try re-inserting it again, adjust the volume on
player clockwise to hear it. Try testing player by SPEAKER set to
ON. Try BANK 1
3.
Audio quality is poor
•
Verify that the audio cord is plugged in securely Make sure the
audio volume is not too loud, adjust the volume control counter
clockwise to correct the problem.
•
Set Volume to Medium. Adjust the TONE. Try the other RCA jack
•
Be sure the recording volume is correct, re-adjust the PC or CD
player volume controls and then play the email/CD player again
to re-record.
4.
Cannot hear the
monitor speaker
•
Set SPEAKER to ON, BANK 1, VOLUME max, confirm you
can hear it. Be sure to re-adjust the VOLUME back to correct
level for on hold
1.
Player not working or
stopped working
Problems
Possible Cause / Solution
P4
110 V
BANK
1 2
8
Ω
600/1200
Ω
Volume
SX9300
Max
DIGITAL
FLASH MEMORY
Technology
OFF ON
9VAC
SPEAKER
TONE
TELEPHONE SYSTEM
MOH Port
AUDIO
IN
PC
speakers
or
Headset
“Y” Patch cable
3.5mm to 3.5mm audio cord
5. Bank2 recording is not
correct.
•
You must 1
st
record the main Bank (Bank1) before you can
record into Bank2
•
If you re-record the Bank1, you need to re-record the Bank2
PC
Speaker
OUT
or
CD player
Headset
jack