Innovate Motorsports MTX-L Скачать руководство пользователя | Manualshive

Страница: 1 / 21

background image

MTX-L

Digital Air/Fuel Ratio Gauge

User Manual

Warning!

The Oxygen Sensor used in this device gets very hot in operation.
Do not touch a hot sensor. Do not let a hot sensor touch a combustible surface.
Do not use the sensor with or near flammable liquids or gases. Failure to heed
these warnings may result in severe burns, explosions, fires, or other dangerous
events.

When installed in the exhaust, the oxygen sensor MUST be connected and
operating with the MTX-L whenever the car is running. An un-powered oxygen
sensor can be quickly damaged when exposed to hot exhaust gases.

1
2
3
...
»

Содержание MTX-L






















Отзывы:

Нет отзывов

Похожие инструкции для MTX-L

Бренд: Panasonic Страницы: 116

Toughbook CF-T7BWATAAM

Бренд: Panasonic Страницы: 12

Бренд: AAT Страницы: 6

SuperStack 3 4300

Бренд: 3Com Страницы: 8

Бренд: 3B Medical Страницы: 7

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Бренд: FANATEC Страницы: 35

Бренд: Dataradio Страницы: 72

Бренд: Napoleon Страницы: 2

Бренд: Harol Страницы: 17

Бренд: Cab Technology Страницы: 10

Бренд: Yamaha Страницы: 124

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

MOLLE PANELS RAM 2500

Бренд: PUTCO Страницы: 4

Бренд: Westfalia Страницы: 18

Бренд: Honda Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды