background image

1

Ice-O-Matic Upright Ice Storage Bins with Ice Shield

 

Installation Instructions and Parts List 

Ice-O-Matic ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and 

outstanding after-the-sale support. To ensure that this bin delivers that same degree of service, we ask that you 

take a moment to review this instruction before beginning the installation of the bin. Should you have any 

questions or require technical help at any point, please call our technical service group at (800)423-3367         

(US & Canada)  

Before You Begin. 

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage.  If 

damage is found, notify the shipper immediately and contact Ice-O-Matic so that we can help in the filing of a 

claim, if necessary. 

!   

Important Cautions

 

•    Avoid excessive tightening force when connecting to the bin drain fitting 

•    Do not apply excessive heat if any sweating of fittings is necessary. Heat conduction through metal may melt 

threads in plastic drain fitting. 

•   When leveling, do not extend any leg more than 1 in. (26mm) for total leg height no greater than 

 2.125 in. (54mm). 

Installation 

1.  Remove all packing material from bin. 

2.  Remove all tape and temporary fastenings from door assemblies and outside of bin. 

3.  Remove set of four legs and any other accessories packed inside bin. 

4.  Lay bin on back, being careful to protect finish, and remove bolts holding skid to bin. 

5.  Screw legs into tapped holes in bin bottom and tighten to seat legs well against bottom. 

6.  Set bin upright. 

7.  Remove protective paper from stainless steel exterior. 

8.  Move bin to permanent location. 

9.  Adjust “foot” at bottom of each leg to level bin in both directions. 

10. Mount icemaker(s) on bin in accordance with icemaker manufacturer's instructions. 

11. Connect drain line to 1" FPT female fitting located in bottom of bin. 

12. Make final connections to icemaker. (Reference the Ice-O-Matic Installation Manual) 

11100 East 45th Ave.

Denver CO 80239

800 423-3367

EP 2138774

Bin Model Numbers

                                              

www.iceomatic.com

9081461-01

B700-30, B1000-48, B1300-48, B1325-60, B1600-60 

01078856R00

 

12/14 

                                             

                                    

1

 

Summary of Contents for B700-30













Reviews: