background image

 

VFCM 15225 Manual V2.1 – May 2007 

IBC

 

IBC Technologies Inc. 
Vancouver, Canada

 

 

VFC 15-150 and VFC 45-225 Modulating Gas Boilers

 

(natural gas or propane)

 

INSTALLATION AND OPERATING INSTRUCTIONS

   

                                                 

              

 

  

 

If the information in this manual is not followed exactly, a fire or explosion may 
result causing property damage, personal injury, or loss of life. 

 

Do not store or use gasoline or other flammable vapours and liquids or other 
combustible materials in the vicinity of this or any other appliance. 

Should overheating occur or the gas supply fails to shut off, do not turn off or 
disconnect the electrical supply to the pump.  Instead shut off the gas supply at a 
location external to the appliance 

WHAT TO DO IF YOU SMELL GAS:  

 

Do not try to light any appliance. 

 

Do not touch any electrical switch; do not use any phone in your building. 

 

Immediately call your gas supplier from a nearby phone. Follow the gas 
supplier’s instructions. 

 

If you cannot reach your gas supplier, call the fire department. 

 

Installation and service must be performed by a qualified installer, service 
agency or the gas supplier. 

Summary of Contents for VFC 15-150


























































Reviews: