background image

1

06/03

P/N 211543B

Customer Service

N53 W24700 South Corporate Circle

Sussex, WI 53089

U.S.A.

A Huffy Company

IMPORTANT!  

We appreciate your purchasing one of our many fine products.  We are sure that you will be very satisfied with your selection. Although
great care and effort have been taken, problems may occur. To ensure prompt and correct handling of any problems, or to answer any
questions, please contact the Sample and Display Technician at 414-820-3440.

REQUIRED TOOLS AND 

MATERIALS:

• 2 People
• Wrenches: (Two each) 7/16”, 1/2”, 9/16”, and 3/4”

or Pliers

• Phillips Screwdriver
• 2 Step Ladders, 8 ft. (2.4 m) 

Model 89025

Please refer to modular category #350 when arranging product for modular display.

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY

RESULT IN SERIOUS INJURY,

PROPERTY DAMAGE AND WILL VOID WARRANTY.

This unit is intended for display purposes only and

should not be used for play. 

To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts.  Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury.  A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly. 

During assembly, if using a ladder use extreme caution.  Two

people are recommended for this operation. 

If technical assistance is required, contact Huffy Sports’ Sample

and Display Technician. 

Serious injury could occur if teeth/face come in contact with

backboard, net or rim. 

Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”

(10 cm) Square poles only.

All instructions and warnings MUST accompany any display item

that is sold. 

Most injuries are caused by misuse and/or not following

instructions.

Use caution when installing this unit.  

Internet Address:  

http://www.huffysports.com

Summary of Contents for 89025























Reviews: