![background image](http://html.mh-extra.com/html/honeywell/silent-knight-wsk-relay/silent-knight-wsk-relay_installation-and-maintenance-instructions_152417001.webp)
SPECIFICATIONS
Maximum Operating Voltage:
3.3 VDC
Maximum Current Draw:
5.0 mA (LED on)
Average Operating Current:
210uA
Maximum Transmit RF Power:
17dBm
Radio Frequency Range:
902-928 MHz
Temperature Range:
32°F to 120°F (0°C to 49°C)
Humidity:
10% to 93% Non-condensing
Battery Type:
4 Panasonic CR123A or 4 Duracell DL123A
Battery Life:
2 year minimum
Battery Replacement:
Upon TROUBLE BATTERY LOW display and/or during annual maintenance
Dimensions: 4
¼
in. H x 4
¼
in. W x 1½in. D
Accessories:
SMB500 Electrical Box (preferred mounting option)
BEFORE INSTALLING
This information is included as a quick reference installation guide. Refer to
the control panel installation manual and the SWIFT Wireless Manual for de-
tailed system information. If the modules will be installed in an existing op-
erational system, inform the operator and local authority that the system will
be temporarily out of service. Disconnect power to the control panel before
installing the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The WSK-RELAY Relay Module is intended for use with a wireless gateway or
wireless fire alarm control panel (FACP). It allows a compatible control panel
to switch discrete contacts by code command. The relay contains one isolated
set of Form-C contacts, which operate as a SPDT switch and are rated in ac-
cordance with the table in this manual. A single relay module may be used to
activate only one output device. Two relay modules must be used in parallel to
activate multiple devices such as a NAC expander. Circuit connections to the
relay are not supervised by the module. The device communicates through a
robust, bi-directional mesh network to the gateway and/or FACP. Rotary dial
switches are provided for setting the module’s address. The module has a
panel controlled LED indicator. (Figure 1)
FACEPLATE
The faceplate includes a magnet for activation and tamper resistance (Figure
2). The faceplate magnet activates communication to the panel, therefore, the
faceplate must be installed for the module to work properly. The magnet also
activates a supervisory tamper fault at the panel if the nameplate is removed.
Do NOT remove this magnet. The faceplate for a wireless module CANNOT be
replaced with the faceplate of a standard wired module.
I56-4272-000
INSTALLATION AND MAINTENANCE INSTRUCTIONS
C1095B-00
FIGURE 2. FACEPLATE INTERIOR:
MAGNET LOCATION
(DO NOT REMOVE)
C1098-00
RELAY CONTACT RATINGS:
CURRENT RATING
MAXIMUM VOLTAGE
LOAD DESCRIPTION
APPLICATION
2 A
25 VAC
PF = 0.35
Non-coded
3 A
30 VDC
Resistive
Non-coded
2 A
30 VDC
Resistive
Coded
0.46 A
30 VDC
(L/R = 20ms)
Non-coded
0.7 A
70.7 VAC
PF = 0.35
Non-coded
0.9 A
125 VDC
Resistive
Non-coded
0.5 A
125 VAC
PF = 0.75
Non-coded
0.3 A
125 VAC
PF = 0.35
Non-coded
FIGURE 1. CONTROLS AND INDICATORS:
12 Clintonville Road, Northford, CT 06472-1610
Phone: 203-484-7161 Fax: 203-484-7118
www.silentknight.com
WSK-RELAY
Wireless Relay Module
1
I56-4272-000
03-02