background image

It is of vital importance, before attempting to 
operate your engine, to read the general 
'SAFETY INSTRUCTIONS AND WARNINGS' 
section on pages 2-6 of this booklet and to strictly 
adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction manual, so as to familiarize yourself 
with the controls and other features of the 
engine.

Keep these instructions in a safe place so that 
you may readily refer to them whenever 
necessary.

It is suggested that any instructions supplied 
with the aircraft, radio control equipment, etc., 
are accessible for checking at the same time.

1

2-6

7

8

9

10-13

18-20

21

25-27

32-33

34

35

15-16

SAFETY INSTRUCTIONS AND WARNINGS 
ABOUT YOUR O.S. ENGINE

ENGINE CONSTRUCTION

NOTES WHEN APPLYING AN ELECTTRIC STARTER

INTRODUCTION

BEFORE STARTING

ENGINE PARTS NAME

INSTALLATION

SILENCER & EXHAUST HEADER PIPE INSTALLATION

FUEL TANK & LINES

THROTTLE LINKAGE, NEEDLE-VALVE EXTENSION

PROPELLER & SPINNER ATTACHMENT

GLOWPLUG

CONTENTS

TYPE 60W CARBURETOR, STARTING

RUNNING -IN, CARBURETOR

CARBURETOR AIR-BLEED ADJUSTMENT

TROUBLE SHOOTING WHEN THE 
ENGINE FAILS TO START

VALVE ADJUSTING

HOW TO SET THE CAMSHAFT TIMING

CARE AND MAINTENANCE

ENGINE EXPLODED VIEWS & PARTS LIST

CARBURETOR EXPLODED VIEWS
& PARTS LIST

GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

27-30

31

36-37

38-39

40-41

42-43

14

17

22-23

24

44

Summary of Contents for FL-70
























Reviews: