(c)
Following consultation with Hills Antenna & TV Systems, we will determine
whether there is a defect, and if so we agree (at our option) to repair, replace or
supply equivalent goods, or pay the cost of any of those remedies to the
consumer.
(d)
The consumer will be responsible for the collection and freight costs of returning
the Equipment to Hills Antenna & TV Systems or to any designated Hills Antenna &
TV Systems Branch Office for repair or replacement (as determined by us).
(e)
Hills Antenna & TV Systems will be responsible for the freight costs to deliver any
new or repaired Equipment to the consumer.
(f)
Please note that a service charge will apply if no fault is identified or if any fault
does not fall within the conditions of this warranty. For details of the applicable
service charge, please contact Hills Antenna & TV Systems prior to making a claim
under this warranty.
5.
The consumer’s right to this warranty will cease to apply
where:
(a)
The Equipment has not been used in accordance with the instructions provided in
the installation instructions supplied with the Equipment, or in accordance with
usual use for that type of equipment;
(b)
Alterations, modifications or repairs have been carried out on the Equipment
6.
This warranty is in addition to any non-excludable legal rights or remedies conferred on
the consumer under any applicable Act and any similar laws. To the extent permitted by
law, Hills
Antenna & TV Systems’ liability for any non
-excludable condition or warranty
is limited to rectifying any defect at its option, as set out in paragraph 4(c).
7.
Subject to the requirements of any applicable Act or legislation and to the extent
permitted by law, no liability (whether expressed or implied) of any nature whatsoever,
is accepted by Hills Antenna & TV Systems for any consequential loss, damage or injury
arising as a result of any fault in the Equipment.
8.
This warranty does not extend to damage to Equipment which occurs during transit or
transportation, or which is caused by any abuse, accident or improper installation,
connection, use, adjustment or repair of goods otherwise than in accordance with
instructions issued by Hills Antenna & TV Systems.
9.
The following applies to consumers who purchased the Equipment in Australia:
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Installation Requirements
Select installation site in consultation with the customer taking the following points into
consideration:
•
Clear signal path to satellite.
•
Structural soundness of the rafters and fascia at the installation point. Rigidity of the
mount installation is imperative.
•
Clear of power lines or other potential hazards.
•
Clear cable run to set top box.
•
The mount should not be installed where the joint of a fascia is between 2 rafters.
In this situation, an adjacent pair of rafters should be used.
•
The mount is not to be installed where debris from surrounding trees can accumulate in
the gutter.
•
The minimum gap between the bottom of the mast base plate and the bottom of the
gutter must exceed 30 mm.
Installation Procedure
1.
Slip three (3) tiles to expose two (2)
rafters as per figure1.
Figure 1
HOW TO FIND US:
NSW
VIC
QLD
TAS
3-29 Birnie Ave
Lidcombe
(Head Office)
Tel: 02 9717 5200
Email:
Cnr Cambria/Bridge St
Keysborough
Tel: 03 9238 2533
Email:
U1/370 Nudgee Rd
Hendra
Tel: 07 3344 3855
Email:
11/15 Pearl St
Derwent Park
Tel: 03 6273 9973
Email:
2.
Assemble the two sections of the mount
as shown in figure 2.
Figure 2
SA / NT
WA
Gold Coast
NZ (
Auckland
)
13-15 Woodlands Tce
Edwardstown
Tel: 08 8275 8400
Email:
11 Abrams St
Balcatta
Tel: 08 6240 9500
Email:
U1/20 Gibbs St
Arundel
Tel: 07 5500 7222
Email:
15C Vestey Dve
Mt Wellington
Tel: +64 9 274 6509
Email:
3.
Place the assembly into the roof so that both plates are firm against the rafters. Check
how the tile sits on the tongue of the mount. If the tongue causes the tile to sit
incorrectly, then it may be necessary to notch the fascia to allow the mount to sit lower
so that the tongue clears the tile.
4
1
Contact us at:
hills.com.au
1300 HILLS 1
1300 445 571
