1
2
Video Access Control Terminal
Quick Start Guide
Appearance
Installation
1. Connect the cables with the connector on the rear
panel of the device.
2. Route the cables through the cable hole of the
mounting plate. The cable holes are on the right side,
left side and lower side of the rear cover.
If the right/left side cable hole is selected, remove the
plastic sheet of the cable hole.
3.Secure the mounting plate
on the wall with 4 supplied
screws.
4.Connect the corresponding
cables.
5.Push the terminal in the
mounting plate from
bottom up.
6.Tighten the screws on the bottom of
the terminal to fix the terminal on the
mounting plate and complete the
installation.
Mic
Camera
LED
Indicator
Card Swiping
Area
Voice Talk
Button
Loud Speaker
Doorbell
Button
Back
Front
Left
Bottom
Before You Start:
Make sure that the device in the package is in good condition and all the assembly parts are included.
Make sure that the wall is strong enough to withstand three times the weight of the terminal.
Set the DIP address before installation.
UD04135B-B
©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instructions on how to use the Product. The software
embodied in the Product is governed by the user license agreement
covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection.
Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all
rights to this manual. This manual cannot be reproduced, changed,
translated, or distributed, partially or wholly, by any means, without the
prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and
are registered trademarks or the subject of applications for the same by
Hikvision and/or its affiliates. Other trademarks mentioned in this manual
are the properties of their respective owners. No right of license is given
to use such trademarks without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE,
IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION
MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO
EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR
AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT
TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF
REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN
ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
DIP S
wit
ch
Network
Wiegand
TF Car
d Slot
Door Lock
and RS485
Micro SIM Card Slot
Serial Port
12V Power
Alarm
DIP S
wit
ch
Network
Wiegand
TF Car
d Slot
Micro SIM Card Slot
Door Lock
Cable Hole
Plastic Sheet
Cable Hole
Plastic Sheet
41.6mm
78mm
218mm
41.6mm
N
o.
Descri
pti
on
DI
P
Sw
itch
S
tatus
1 to 4
RS-
485 Address
2:
S
ecure Door
Control
U
nit
0: Card
R
eader
5
RS-
485 Direc
ti
on under
Terminal Mode
1:
Up
stream
0: Do
w
nstream
6
W
ork Method
1: Card
R
eader
0: Terminal
7
W
iegand
P
rotocol
(Available
w
hen
B
it 6 is 1)
1:
W
iegand 26
0:
W
iegand 34
8
Matched
R
esistance
(Available
f
or
RS-
485
P
rotocol)
1:
E
nable
0: Disable
The DIP switch from left to right is from low bit to the high bit.
If the switch is towards ON, it means the binary value is 1, while OFF
means 0.
For Example, if the DIP switch is as the picture shown on the right, the
binary value is 0000 1100, which means the decimal value is 12.
