background image

FOR HLNA0301

OWNER’S MANUAL AND EXPLODED VIEWS

•  Entire contents ©2013 Helion RC
•  Before using your product, review all documentation and inspect the products carefully. If for some reason you decide it is not 

what you wanted, then do not continue with unpacking, setup or operation of your product. Your local hobby dealer cannot ac-
cept a product for return or exchange after partaking in actions that produce wear and tear.

•  Read, understand and follow all instructions and accompanying material carefully before operating or assembling your vehicle 

to prevent serious damage to your vehicle. Failure to complete these tasks properly or intentional aversion to the content will be 
considered abuse and/or neglect.

•  Product specifications are subject to change without notice. Due to ongoing development, the actual product may vary from 

images shown.

•  This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
•  This product is not a toy! (14+) Recommended for ages 14 and up. Adult supervision required for ages under 18 years old. 

Contains small parts, keep out of reach of children 3 years of age and younger.

LENGTH

386.40mm (15.21in)

WIDTH

249mm (9.80in)

HEIGHT

153.15mm (6.03in)

WHEELBASE

283mm (11.14in)

WHEEL DIAMETER

55.88mm (2.2in)

WHEEL OFFSET

12mm Hex, AE/KYO Compatible

WEIGHT*

1560g (3.44lb)

BATTERY

3,000mAh NiMH 7-CELL, 8.4V

MOTOR

Metric 12T High Speed, 540 Size

RADIO

HRS-3.1 2.4GHz 3-CHANNEL

CHARGER

AC 1Amp

*APPROXIMATE OUT-OF-THE-BOX WEIGHT

Scan this QR code 

with your smart 

phone to view the 

getting started video 

for this product. 

Summary of Contents for Criterion HLNA0301









































Reviews: